Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
Vertical steam
Self Clean
Features
1. Soleplate
2. Spray nozzle
3. Water inlet cover
4. Variable steam button/Self clean button
5. Spray button
6. Steam burst button
7. Power cord
8. Indicator light
9. Temperature dial
Before first use
•
Remove any sticker, protective foil or storage cover from
the soleplate.
•
Heat up the iron to maximum temperature and iron over
a piece of damp cloth for several minutes on the
purpose of removing any residue on the soleplate.
Note: It is normal that a strange odour will eminate from the
unit for the first time it is used.
Assembly
Warning! Before assembly, make sure that the appliance is
switched off and unplugged.
Filling the water tank (Fig. A)
In order to be able to use the steam function, you will first
need to fill the water tank with water.
•
Unplug the Iron and take it to a water outlet
•
Lift the water inlet cover (3).
•
Hold the appliance at an angle.
•
Fill the appliance with water to the required amount via
water outlet, or using a filling jug.
•
Close the water inlet cover (3).
Warning! Never fill above the maximum filling level
indicated on the appliance. Normal tap water can be used,
but if you live in a hard water area the use of distilled water
is recommended. Do not use chemically de-scaled water.
Use
Warning! Do not leave the appliance unattended while it is
connected to the power supply and during the cool down
period.
6
(Original instructions)
•
Connect plug to outlet and turn temperature dial to your
desired setting, which is dependant on the fabric of the
garment (Fig.B).
•
The indicator light (8) will be illuminated. Refer 'IRONING
TIPS' in this manual.
•
Once soleplate has reached its preset temperature, the
indicator light will be off, then you can set the steam
button to your desired steam output or dry position and
begin ironing.
Warning! Do not touch the hot soleplate at any time before
cooling down!
•
Press spray button (5) a couple of times to moisten the
laundry if necessary, before spraying make sure that
there is enough water in water tank.
•
The steam burst function can be used at max
temperature, to remove stubborn creases.
•
The iron has an anti-drip function: if ironing garments for
a long time, the soleplate temperature will fall off, the iron
will stop producing steam automatically and no water
droplets can emit from the soleplate.
•
The steam burst can also be applied when holding the
iron in a vertical position, so this is useful for removing
creases from hung clothes, curtains, etc.
Self-clean function
The unit should be cleaned regularly according to hardness
of water and frequency of use.
•
Fill the water tank and set the temperature selector to
Max position.
•
Connect to power supply, the indicator light will be
illuminated, make sure Steam button is in the Dry
position, then place iron upright as shown in figure.D
Warning! never pour white vinegar or other liquid cleaners
for eliminating calcium into water tank!
•
Once the indicator light is off, disconnect the plug, hold
the iron over the sink and turn steam button to SELF
CLEAN position (Fig.C) with a little force. Steam and
boiling water will come out of the soleplate while ensuring
impurities and flakes are flushed out.
•
Release the button as soon as the water in the water
tank is used up.
Auto-decalcification feature
There is a decalcification box inside the appliance, which is
able to absorb insoluble calcium ion and emit soluble natrium
ions so that water can be softened, and calcium build up will
be greatly reduced.
Note: In order to keep soleplate smooth, never iron over any
metal material such as zips, etc.
Ironing tips
•
Always check first whether a label with ironing
instructions is attached to the article.
Publicité
Table des Matières
