Télécharger Imprimer la page

MPA ORION PLUS Notice De Montage page 3

Publicité

Montage der Rahmen, Anordnung der Stützenverbinder
g
g
Montage des cadres, disposition des connexions d'appui
g
Montage van de frames, plaatsing van de steunverbindingsstukken
g
Frame assembly, support connection arrangement
Abb. 1
Abb. 1 a
u u
1
Stützprofil
Stützenverbinder
1
2
Profilé d'appui
Connexion d'appui
Steunprofiel
Steunverbindingsstuk
Support frame
Support connection
Abb. 2
Abb. 2 a
u u
Sicherungsstift
3
4
Cheville de fixation
Bevestigingspen
Securing pin
2
5
4
Fußplatte
Kunststoffkappe
5
Plaque de base
Plastique de protection
Voetplaat
Kunststofkap
Footplate
Plastic cap
Aufbauanleitung
D
g
g
Notice de Montage
F
g
Handling voor montage
NL
g
Assembly instruction
GB
Zwei Stützprofile im Abstand der Stützenverbinder anordnen.
D
Stützenverbinder entsprechend Abb. 1 (die Pfeile zeigen in Richt-
ung des Fußbodens) einsetzen und mit einen Gummihammer
o.ä. in die Stützprofile einschlagen.
Achtung! Die Fixierprägung der Stützenverbinder (Abb. 1 a)
Sicherungsstifte, Fußplatten und Kunststoffkappen einsetzen
(Abb. 2).
Montage des châssis, utilisation d'un côté et des deux côtés.
F
Disposer les deux profilés d'appui entre les connexions d'appui.
Placer les connexions d'appui suivant l'illustration 1 (les flèches
indiquent la direction du sol) et insérer avec un marteau en caout-
chouc les profilés d'appui.
Attention! Les connexions d'appui (fig. 1) doivent s'enclencher
Placer les Chevilles de fixation, plaques de base et plastiques de
protection (fig. 2).
Twee steunprofielen op de afstand van de steunverbindingsstuk-
NL
ken plaatsen. Steunverbindingsstukken overeenkomstig afb. 1
(de pijlen wijzen in de richting van de vloer) inzetten en met een
rubberen hamer of dergelijke in de steunprofielen slaan.
Opgelet!
Bevestigingspennen, voetplaten en kunststofkappen inzetten
(Afb. 2).
3
Arrange two support frames at the correct distance for the support
GB
connection. Fit the support connections as shown in Ill. 1 (the
arrow points in the direction of the ground) and use a rubber ham-
mer (or similar) to tap them into the support frames.
Attention! The locking pieces for the support connections (Ill. 1 a)
Fit the securing pins, footplates and plastic caps (Ill. 2).
muß auf beiden Seiten in die Stützprofile einrasten
(Abb. 2 a).
des deux côtés des profilés d'appui (fig. 2 a).
De fixeeradhesie van de steunverbindingsstukken
(Afb. 1 a) moet aan beide kanten in de steunprofielen
sluiten (Afb. 2 a).
must be snapped in position on both sides in the sup-
port frames (Ill. 2 a).
3

Publicité

loading