Bradley Keltech HL Serie Manuel D'installation page 19

Installation
Table of Parameters for DC Option: RS-485 Modbus
Parameter Name
Analog Input -1999 .000 to 9999 .000°F
-1128 .000 to 5537 .000°C
Analog Input Error None (61)
Open (65)
Fail (32)
Shorted (127)
Measurement Error (140)
Bad Calibration Data (139)
Ambient Error (9)
RTD Error (141)
Not Sourced (246)
Calibration Offset -1999 .000 to 9999 .000°F
-1128 .000 to 5537 .000°C
Digital in 5 Inactive (41)
Active (5)
Digital out 6 Off (62)
On (63)
EZ-KEY Inactive (41)
Active (5)
Control Mode Active Off (62)
Auto (10)
Manual (54)
Heat Power 0 .0 to 100 .0%
Set Point -1999 .000 to 9999 .000°F
-1128 .000 to 5537 .000°C
Remote Set Point No (59)
Yes (106)
Remote Set Point Type Auto (10)
Manual (54)
Process Value -1999 .00 to 9999 .000°F
-1128 .000 to 5537 .000°C
Control Mode OFF (62)
Auto (10)
Manual (54)
Close Loop Set Point 40-160 std
40-170 T170 Option
40-180 T180 Option
40-190 T190 Option
40-200 T200 Option SPCL
Open Loop Set Point 0 to 100%
Display Units Fahrenheit (30)
Celsius (15)
Address Modbus 1-247
Baud Rate 9600 (188)
19200 (189)
38400 (190)
Parity Modbus None (61)
Even (191)
Odd (192)
Modbus Units Fahrenheit (30)
Celsius (15)
Modbus Word Order Low-High (1331)
High-Low (1330)
Non-Volatile Save Yes (106)
No (59)
NOTICE! For adjusting Modbus address, baud
rate and parity, customer needs to set
on Watlow controller per Watlow manual.
Bradley • 215-1823 Rev. F; ECN 18-17-017
Range Map 1
360
362
382
1328
1042
1368
1882
1904
2172
2200
2202
402
1880
2160
2162
1838
2482
2484
2486
2490
2488
2494
Map 2 Default Data Type
360 -- FLOAT
362 None UINT
382 Factory Set FLOAT
1568 -- UINT
1162 -- UINT
1608 -- UINT
2362 Auto UINT
2384 -- FLOAT
2652 -- FLOAT
2680 No UINT
2682 No UINT
402 FLOAT
2360 Auto UINT
2640 Factory Set FLOAT
2642 -- FLOAT
2308 °F UINT
2962 1 UINT
2964 9600 UINT
2966 None UINT
2970 °F UINT
2968 Low-High UINT
2974 Yes UINT
uint = Unsigned 16 bit int
dint = Long 32 bit
RWES = Readable, Writable, EEPROM (saved), User Set (saved)
3/29/2018
HL-Series Tankless Heater
Read/
Write HL Series Meaning
R Process Value
R Process Value Sensor Error
RWES Process Value Calibration
R Flow Activation
R AL Only Alarm Status
R EZ-Key
R Control Loop Mode
R Duty Cycle Output %
R Heater Set Point
RWES Remote Set Point Enable
RWES Remote Set Point Control Mode
R Process Value
RWES Control Loop Mode
RWES Heater Set Point
RWES Manual Mode Set Point
RWES Controller Display Units
RWE Modbus Address
RWE Modbus Baud Rate
RWE Modbus Parity
RWE Communication Units
RWE Modbus Word Order
RWE If set to yes, all values to the control will
be saved from EEPROM
Legend
string = ACSII (8 bit per character
float = IEEE 754 32 bit
19