English - optrel medmaxx Mode D'emploi

English

Introduction
This product is eye and face protection with a clear view and is intended for use by
medical professionals or emergency services personnel�
Safety instructions
Read these operating instructions carefully before using the equipment� Incorrect
use could endanger life and limb and void warranty claims against the manufacturer�
Performance of the PPE / Applications / Risks
The product offers an unlimited, clear view of your patient� If the air humidity /
temperature difference is high, the visor can fog up, resulting in poor visibility�
If the headband is set incorrectly, there is a risk that the product will detach from
the head and fall�
Precautions and protective restrictions
• Before using the product, always check that the equipment is complete and that no
damage has occurred during transport� Never use faulty or damaged equipment�
• The user must be familiar with the correct use of his/her personal protective
equipment�
• Appropriate protective clothing must also be worn to protect the rest of your body�
Materials in contact with the skin of the product can cause allergic reactions in
sensitive individuals�
• There is a risk of bumping due to the larger size (head with visor)�
• If the headband is set incorrectly, there is a risk that the product will detach from
the head and fall�
• The product is intended for use by medical professionals or emergency services
personnel�
• The product protects against drops and splashes of liquids� This reduces the risk
of droplet infection� Due to its design, full protection against viruses, bacteria or
other biological agents is only given to a limited extent�
• The product can be combined with face masks�
Warranty & liability
For the warranty conditions, please refer to the instructions provided by your national
sales organisation� For more information, please contact your retailer� The warranty
only applies to material and manufacturing defects� In the event of damage caused by
unintended use, tampering or any use not intended by the manufacturer, the warranty
or liability shall be void� Similarly, liability and warranty are void if spare parts other than
those sold by the manufacturer are used�
Estimated service life
The product does not have an expiration date� The product can be used as long as no
visible or invisible damage or malfunctions occur�
How to use (Quick Start Guide) p� 3
1� Head strap� Set the upper adjusting strap to suit your head size� Push in the locking
knob and turn it until the head strap is fitting securely but without applying pressure�
2� Distance from eyes� The distance between the protective glass and the eyes can
be adjusted by releasing the locking knobs� Adjust both sides equally and do not
tilt� Then tighten the locking knobs again�
3� The vizor angle can be adjusted using the rotary knob�
4� After use, the product must be cleaned and disinfected thoroughly�
Cleaning, disinfection and Maintenance
Manual cleaning: remove sweatband and comfort band� Use a clean cloth dampened
with soapy water to clean the visor inside and out and allow it to dry in a clean
environment�
Machine cleaning: remove sweatband and comfort band� Select a cleaning program
with a maximum temperature of 70 ° C�
Manual disinfection: by wiping or spraying with a commercially available disinfectant�
Machine disinfection: Select a disinfection program with a maximum temperature
of 70 ° C�
UV disinfection is possible�
Maintenance: The visor is to be replaced if it is
- deformed or cloudy due to high temperature
- has been scratched or deformed by a shock or mechanical influence
- became cloudy due to chemical influence
Storage
The product must be cleaned and disinfected thoroughly before storage� Storage at
room temperature and low humidity�
Removing / installing the visor (p� 2)
To remove the visor:
• Unscrew the knobs
• Remove spacers
• Take off four
Attaching the visor: in reverse order�
Technical data
(We reserve the right to make technical changes at any time)
Weight
Material
Opterating temperature
Storage temperature
Shape stability
Approvals
Declaration of conformity
See the Internet address on the last page�
Legal information
This document complies with the requirements of EU Regulation 2016/425 section
1�4 of Annex II�
Notified body
For detailed information see last page�
10
250g / 8�82 oz
Headband: Polyethylene
Visor: Polycarbonate
– 10°C to + 55°C / 14°F to 131°F
– 20°C to + 80°C / – 4°F to 176°F
Headband: up to 220°C / 428°F
Visor: up to 137°C / 279°F
EN166
AS/NZS 1337
ANSI OS U5 Z87
ANSI Z87
OS 1 FT EN 166 CE
complies with CSA Z�94�3