Assembly Of Supporting Shank; Assembly Of Standard Step Guard Rail; Assembly Of Plug-In Step Guard Rail; Assembly Of Platform Guard Rail, Lateral, Standard - zarges Z600 Notice De Montage Et D'utilisation

5.2.6

Assembly of supporting shank

Exercise caution while introducing the
supporting shank, as there is danger of
getting squeezed.
The gusset plate (15/4) can also be in-
stalled on the inside during the platform
assembly.
• Introduce the supporting shank (15/3) into the gusset
plates (15/4) in such a way that the square head bolts
are introduced into the screw channels.
• Push the supporting shank (15/1) fully against the
platform cheek (15/2).
• Install four mounting nuts (15/2) on each side and
tighten with a torque of 25 Nm.
5.2.7

Assembly of standard step guard rail

The step guard rail is pre-assembled ex-
cept for the guard rail fastener. The step
guard rail can be mounted at the left as
well as at the right.
When assembling the step guard rail on
the industrial access steps, the dimension
"X" (17) must be observed for the lower
guard rail fastener.
The dimension "X" is as follows:
Industrial access steps
Industrial access steps
• Push the guard rail fasteners (16/1) over the rail and
the rail supports (16/4) and (17/1) till the relevant rail
support (16/4) is aligned to the guard rail fastener.
• Turn the guard rail fasteners in such a way that the
flat side faces the stile or the platform cheek. Install
the mounting nut (16/2), do not tighten it.
• Place the step guard rail on the stile of the stairway
and platform cheek (17). Use two M8x70 mounting
screws (16/3) with toothed lock washers each to in-
stall the guard rail fastener in the slot nuts.
• Tighten the M8x70 mounting screws (16/3) with a
torque of 17 Nm.
• Tighten the mounting nut (16/2) with a torque of
17 Nm.
In case of stationary bridging steps, the
side platform guard rail is to be mounted
before installing the second guard rail,
refer to Section 5.2.9.
GB
5.2.8
• Align the pre-assembled rail holders (18/2) with
• Align the other rail holders at the spacing of the step
• Tighten the rail holders with socket screws (18/3) (25
• Insert the locking pins (19/2) and lock them by turning
• It should be possible to remove the step guard rail
5.2.9
45° w 365 mm
60° w 300 mm
• Push the guard rail fasteners (20/4) over the rail sup-
• Use two M8x70 mounting screws (20/2) with toothed
• Push the rail tube (21/2) on the joint (21/1) of the step
• Place the rail tube (21/5) on the guard rail support
• Insert intermediate rail (22/2) between the guard rail
• Secure the intermediate rail on the step side (22/3)
• Fix and tighten the intermediate rail on the other side
• Tighten the M8x70 mounting screws (20/2) of the rail
- 24 -

Assembly of plug-in step guard rail

The step guard rail and the rail holder are
pre-assembled. The step guard rail can
be mounted at the left as well as at the
right.
When assembling the step guard rail on
the industrial access steps, the dimension
"X" must be observed for the lower guard
rail holder.
The dimension "X" (17) is as follows:
Steps
Step ladders
brackets (18/1) starting from the lower step stile end
(dimension "X") with 3 M8x20 socket screws (18/3)
with plain washers and the slot nuts in the screw
channels.
guard rail supports. Plug the step guard rails (19/1)
into the rail holders (19/3) and align the holders to the
rail supports.
Nm).
the clips (19/4).
easily and without seizing.

Assembly of platform guard rail, lateral, standard

In case of stationary bridging steps, the
side guard rail consists only of the inter-
mediate rail (22/2) and the rail tube (21/2)
and (21/5), the installation is done in the
same way.
port (20/1) till the relevant rail support is aligned to
the guard rail fastener (20/3) (holes must be aligned).
Install the mounting nuts (20/5), do not tighten them.
lock washers each to install the guard rail fastener
equipment in the slot nuts.
guard rails and tighten with countersunk bolt, plain
washer and cap nut (21/3).
(21/6) and fasten tightly with M6x30 socket screw.
Seal the hole with plastic plugs (21/4).
supports.
with countersunk screw.
with M6X30 socket screws, seal hole with plastic
plug.
fastener with a torque of 17 Nm.
45° w 365 mm
60° w 300 mm.
o
N 291311