Electronic Speed Control Setup; Spécification - Maverick VADER XB Manuel D'instructions

Electronic Speed Control
Specification
•
150 Amps continuous current
•
Case dimensions: 68mm x 55mm x 45mm
•
Silicone Wire 12 Gauge
•
Weight 150g with connectors and switch
Setup Procedure
MSC-27BL 150A Brushless ESC
1. With the speed control switch set to off, plug in a suitable battery pack.
2. Make sure the throttle trim is set to the centre, the TH channel is set to REV and the Throttle dual rate is set to 10.
3. Hold the set button on the switch and turn the ESC on.
4. The ESC will beep, leave the throttle trigger in neutral and press the set button once.
5. Hold full throttle on the transmitter and press the set button once.
6. Hold full brake on the transmitter and press the set button once.
Programmable settings
The MSC-27BL ESC has a number of programmable modes that can be altered to suit a variety of functions. Each set of green LED flashes/beep
represents the Programmable Mode (1 flash = Running mode, 2 flashes = Drag brake Force and 3 flashes = Auto-LiPo settings etc..) and each set
of red LED flashes/beep represents that Modes value.
See the table below for all the Programmable Modes and there values. The number 5 is represented by one long flash/beep so it can easily be
identified. This makes the number 6 one long flash/beep followed by one short flash/beep and so on. When you enter the setup mode you need to
keep the button pressed until you enter the desired program mode (green flashes/beeps). Once you reach that mode release the button and that
will allow you to change the mode value (red flashes/beeps).
You need to switch off the ESC to save the settings and then re-do the process to change a different mode or mode value setting. If you lose your
way with setup you can return the unit to default settings by turning on the ESC, keeping the transmitter in neutral and pressing the setup button
for 3 seconds. Both red and green LED's will flash together 3 times to confirm this.
To enter the programmable settings on the ESC you must do the following
1. While switching on ESC hold down the setup button. Continue to hold the setup button while the LED's flash
2. Continue to hold the setup button until the green LED's flash. Each flash represents the programmable mode number.
3. Release the setup button when you reach the desired mode. You are now in the program mode setting.
4. Press the setup button to change the mode value. Each mode value will have different amounts of red LED flashes.
5. In order to save the changes and the settings you must switch off the ESC. When you next switch it back on it will have saved your new
settings. To make further alterations you need to re-enter the mode values again.
G Programmable
R Values
E
1. Running Mode
E
N
2. Drag Brake
3. Voltage Protect
L
E
4. "DRRS" Punch
D
5. Brake Force
6. Reverse Force
7. Initial Brake
8. Neutral Range
9. "AMTS" Timing
10. Overheat
Protection
11. Motor Rotate
12. LiPo Cells
•
•
•
•
1 2
For/ For/Rev/
Brake
Brake
0% 5%
2.6V/Per 2.8V/
None
Cell Per Cell
Level 1 Level 2 Level 3 Level 4 Level 5
25% 50% 750%
750%
25% 50%
0%
Drag
Brake
6% 9%
1 2
Enabled
CW
CCW
2 Cells 3 Cells
Auto
7.4V 11.1V
Calculate
BEC Voltage 5.75V/3A
Sensorless
Battery Input: 6-18 cells (7.2V-21.6V) Ni-MH, 2-6 cells (7.4V-22.2V) LiPo
Burst Current: 1080A
Mode Value RED LED
3 4 5
For/
Rev
10% 20% 40%
3V/Per
3.2V/Per
Cell Cell
100% Disable
100%
20% 40%
12%
3 4 5
4 Cells 5 Cells
14.8V 18.5V
5
6 7
60% 80% 100%
3.4V/Per Custom
Cell
Level 6 Level 7 Level 8 Level 9
6 7
6 Cells
22.2V
8 9
Custom
8 9