Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Sauf indication contraire :
- a = e mini.
- ou z = e mini.
- ou s ≥ 0.5 x e mini.
- Soudure En bouchon s > e mini.
- Soudures plates au possible.
- Pieds de cordon convenablement
mouillés.
- Soudures en position PA ou PB.
- Soudures brossées et sans
projections.
SPRING TENSION
The impact-wrench support trolley is equipped with a spring that balances the weight of the impact wrench.
Be careful not to knock the adjusting screw as this will damage it and may prevent it from working.
PIN
The impact-wrench support trolley is equipped with pins to prevent the arm from opening when the product is moved
or during storage. Simply close the arm and position the pins in the appropriate position in the clevis pins.
During use, it is recommended to place them in the first arm's tube holes.
26
TROLLEY IW1
Assembling the impact-wrench
1- Lock the arm by inserting the pins.
2- Adjust the balancing effort to the minimum setting using the clam-
ping screw located under the seat.
3- Insert four of the screws (M6x30) into the impact wrench's handle
and in the impact-wrench connector (corner plate), then tighten the
screws with the four lock nuts (M6) (Torx Allen key [T30], flat spanner
[10 mm]).
4- Fit the male-hose adaptor into impact-wrench's air inlet and tighten
it (flat spanner [26 mm]).
5- Hold the impact-wrench support in place by aligning the moun-
ting-bolt holes on the impact wrench's handle with the impact-wrench
plate's holes, found under the ball joint. Then, affix the impact wrench
by tightening the four screws (M6x30) that pass through the impact-
wrench support and the impact-wrench plate (Torx Allen key [T30]).
It is recommended that two people be present to undertake this
operation.
Indice:
MPF / Commentaire:
A
-
26087.61 g
6- Connect the hose to the impact-wrench support and secure it with
Masse:
Non
Traitement:
Surface:
mm²
(Code ST Gys)
the single-ear hose clamp (pincers). Be careful not to cut the hose.
Désignation:
Montage clé
-
Produit:
19_11149
Nom du fichier CAO:
CHAUDRONNERIE
Ce document est la propriété de la société GYS et ne peut en aucun cas être transmis à quiconque sans son accord.
USAGE
To increase the balancing force (to further raise the impact wrench), simply turn
the adjusting screw under the seat clockwise using a ratchet spanner and a
spark plug socket (21 mm).
Moving in the opposite direction will relax the spring and reduce the balancing
force (to further lower the impact wrench). The system does becomes slightly
unbalanced when the arm is moved back towards oneself (the impact wrench
tends to move upwards), so it is advisable to adjust the balancing so as to limit
the force with which the wrench moves upwards (ideally being balanced gently).
Screw (M6x30) x8
Lock nut (M6) x4
Impact wrench x1
Impact-wrench handle x1
Male-hose adaptor (Ø 12 mm) x1
Single-ear hose clamp (19.5 mm) x1
Symbolisation selon ISO 2553 et ISO 4063
Date modification:
Modifié par:
jonathanb
17/03/2021
Jonathan BONILLO
Etabli par:
17/10/2019
Date:
A3
Statut:
Format :
Études
1:3
Echelle:
Indice:
Feuille:
-
1/1
A
EN
Publicité
Table des Matières
