• Install the solar module
Use only the manufacturer's original solar
modules.
Reliable operation can only be ensured if sufficient
energy is supplied also in winter when there is little
sunshine. Therefore, install the solar module
vertically towards south.
1
Install the mounting bracket
2
Wall installation
Mark, drill and fasten the mounting bracket with
screws. Install the solar module and fix it with screws.
3
Roof installation
Install the mounting bracket.
Do not drill holes into the garage roof.
!
Avoid leaks.
A flagstone, e.g., makes a good base. Bore holes in
the flagstone and fasten the bracket. Place on the
garage door and align south.
4
Electrical connection
Use a cable suitable for outdoor installation
or lay a cold-resistant PVC cable in conduit 4a
Connection. Mind correct polarity 4b.
!
The battery has an internal 20 A blade-type
fuse. Charge. Function control incremental
display 4c.
Dismantling the operator
•
1. Pull out the mains plug and disconnect all existing
terminals.
2. Disconnect door and operator. Fix door.
3. Proceed according to points 3 to 13 of the
installaton Instructions but in reverse sequence.
• Programming the operator
14
Control elements
The controls for programming the door operator are
protected by a transparent cover. The transparent
cover can be opened with a screwdriver. After the
operator has been programmed, the transparent
cover must be closed again.
A. Numerical display shows the menu stage as well
as the selected value.
a. Incremental display, indicates the power being
supplied by the solar module and flashes to
acknowledge taught handheld transmitter codes.
B. Button
during the setting / adjustment phase
serves as an "up" button and outside the menu as
a start button.
C. Button
during the setting /adjustment phase
serves as a "down" button.
D. Button
is used to call up the setting/adjustment
menu, to change the menu stages and to store the
settings.
The programming of the control unit is menu-driven.
By pressing button
, the menu guide is called up.
The numbers displayed indicate the menu stage.
After approx. 2 seconds, the display flashes and the
setting can be altered via buttons
selected setting is stored with button
programme jumps automatically to the next menu
stage. By repeatedly pressing button
stages can be skipped. To quit the menu, press
button
until "0" is shown again. Outside the menu,
button
can be used to generate a start impulse.
Before programming
- Allow door to engage into the carriage.
- Connect the Accu-Pack drive. Light turns on.
- Observe the hand transmitter instructions.
Retain these installation, operating and maintenance instructions for the full duration of the operator's service life!
15
Menu stage 1: Programming the start
function for the hand transmitter
Briefly press button
the display flashes, press and keep pressed for
approx. 1 second the button of the hand transmitter,
with which you later wish to start the operator. As
soon as the code has been read, the red point
display (a) flashes four times before quitting. Figure
0 will be displayed. Menu finished.
Further hand transmitters (up to a maximum of 10)
can be programmed.
16
Menu stage 2: Programming the light
function for the hand transmitter
Press key
briefly and figure 1 will be displayed.
Press key
displayed.
Press the second button at the transmitter with which
the 4-min light is to be switched on. As soon as the
code has been read in, the red point display (a) will
flash four times to acknowledge the entry. Figure 0
will be displayed. Menu finished.
Deleating all the hand transmitters programmed
for the operator:
Plug in the operator's main plug while pressing
button
.
17
Menu stage 3: Setting/adjusting the top end-
of-travel position
Keep button
appears in the display 17 a.
Wait a short while until the 3 starts flashing.
Press button
and make sure that the door travels in
the OPEN direction.
If the door closes in the wrong direction, after
having pressed
!
another 3 seconds. "3" flashes briefly. The
travelling direction is altered.
Now travel by pressing button
end position OPEN 17b.
By pressing button
into direction CLOSE.
Once the desired OPEN end-of-travel position has
been reached, press button
the OPEN end-of-travel position and "4" appears in
the display.
18
Menu stage 4: Setting/adjusting the bottom
19
end-of-travel position
Wait a short while until "4" starts flashing.
Press button
. The operator causes the door to
travel in the CLOSE direction as long as the button is
pressed. The position can be altered to the OPEN
direction via button ..
Once the desired CLOSE end-of-travel position has
been reached, press button
the CLOSE end-of-travel position and "0" appears in
the display.
19
Force-learning cycle
We recommend setting the suitable door type in
!
menu stage 8 prior to the force-learning cycle.
and
. The
. And the
During this opening and closing cycle, the
, menu
operator learns the force required to open and close
the door.
A force limit does not apply!
must not be interrupted. During these cycles must
not be interrupted. During these cycles "0" appears
in the display.
- Press button . The operator causes the door to
open until the top end-of-travel position has been
. "1" is displayed. As soon as
once again and figure 2 will be
pressed for 3 seconds. Number 3
, keep button
pressed for
into the desired door
, the position can be corrected
. The operator stores
. The operator stores
The cycles
reached.
- Now press button
again. The operator causes
the door to close until the bottom end-of-travel
position has been reached.
- After approx. 2 seconds, "0"disappears.
Caution! If the force setting is too high, persons may
be placed at risk of injury.
The factory setting is 4!
20
Checking the force limit facility
- Place an obstruction (e. g. operator's cardboard
box) underneath the doors's closing edge.
- Starting from the OPEN end-of-travel position,
actuate the door to close.
- The door travels towards the obstruction, stops
and travels back to the top end-of-travel position.
If the door springs have been changed or altered,
then the force learning cycle must be repeated:
proceed to menu stage 5 and keep button
pressed for 3 seconds. "0" appears in the display.
Then complete the force learning cycle as explained
under point 19.
GB