General Power Tool Safety Instructions; Maintenance Instructions - Makita HB500 Instructions Originales

en

General Power tool saFety instructions

1. KNOw YOUR POwER TOOl
Read and understand the owner's manual and
labels fixed to the tool. learn its application and
limitations as well as the potential hazards .
2. EARTH All TOOlS
Ensure that (where applicable) suitable earthed
cords and plugs are used and correctly
connected.
3. KEEP gUARDS IN PlACE (where applicable),
in working order and in correct adjustment and
alignment.
4. REMOVE ADJUSTINg KEYS AND wRENCHES.
Form a habit of checking to see that keys and
adjusting wrenches are removed from tool
before turning it on.
5. KEEP wORK AREA ClEAN
Cluttered areas and benches invite accidents.
Floor must not be slippery due to oils, or dust.
6. AVOID DANgEROUS ENVIRONMENT
Don't use power tools in damp or wet locations
or expose them to rain. Keep work area well
lighted. Provide adequate surrounding work
space.
7. MAKE wORKSHOP SAFE
Use padlocks, master switches, remove keys.
Visitors should be a safe distance from work
area
8. DON'T FORCE TOOl
It will do the job better and more safely at the
rate for which it was designed.
9. USE CORRECT TOOl
Don't force tool or attachment to do a job it
was not designed for.
10. wEAR PROPER APPAREl
Do not wear loose clothing, gloves, neckties or
jewellery (rings, wristwatches) which may get
caught in moving parts. NONSlIP footwear is
recommended.
wear protective hair covering to contain long
hair. Roll long sleeves above the elbow.
4
11. USE SAFETY gOgglES (Head Protection)
wear approved safety goggles at all times.
Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses. Also, use
face or dust mask if cutting operation is dusty,
and ear protectors during extended periods
of operation.
12. SECURE wORK
Use clamps or a vice to hold work when
practical. It's safer and frees both hands to
operate tool.
13. DON'T OVERREACH
Keep proper footing and balance at all times.
14. MAINTAIN TOOlS wITH CARE.
Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating
and changing accessories.
15. DISCONNECT TOOlS
when not in use, before servicing and when
changing accessories such as bits and cutters,
disconnect tools from the power supply.
16. USE RECOMMENDED ACCESSORIES
Consult owners manual for recommended
accessories. Follow the instructions that
accompany the accessories. The use of
improper accessories may cause hazards.
17. CHECK DAMAgED PARTS
Before further use of the tool, a guard or
other part that is damaged should be carefully
checked to ensure that it will operate properly
and perform its intended function. Check for
alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any
other conditions that may affect operation. A
guard or other part that is damaged should be
properly repaired or replaced.
18. NEVER lEAVE TOOl RUNNINg
UNATTENDED.
Turn power off. Don't leave the tool until it
comes to a complete stop.
MaGnetic drill
saFety instructions
• Always inspect the whole unit before use.
• Regular maintenance is essential - check nuts,
screws etc. for tightness before each use.
• Check cable and plug for damage.
• Never use blunt or damaged cutters.
• Never use a larger diameter cutter than
specified for the machine
• Always use the safety guards (where fitted)
and ensure they are operating correctly.
• Always wear goggles and gloves
• Remove rings, watches, ties etc. that could
tangle in the moving parts.
• Secure the unit with the safety strap before
drilling.
• The machine is for use on steel from 6 mm
thick, with no air gap between the magnet core
and the workpiece. Curvature, paint and surface
irregularities create an air gap. Keep the air gap
to a minimum.
• Keep the magnet and workpiece clean & free
of debris and swarf.
• Do not start the motor before ensuring that
the magnetic stand is clamped firmly to the
workpiece.
• Only use a general, non-oil-based metal
cutting coolant diluted with water.
• while drilling vertically or overhead, use a
cutting paste or an appropriate coolant spray.
• Always disconnect from the power source
before changing cutters or working on the
machine.
• In the event of a jammed cutter, disconnect
from the power supply, and free the jam before
reconnecting the tool.
• On swivel machines, ensure that the swivel
base is locked in the required position.
• Do not attempt to change speed while the
drill is running.
• Only use accessories recommended by the
manufacturer.
• Never lift or carry the unit by the power cord,
always use the handle.
• Never modify the tool in any way.
IMPORTANT! –
TO PREVENT DAMAgE TO THE CIRCUITRY, NEVER USE ElECTROMAgNETIC DRIllINg
MACHINES AND wElDINg EqUIPMENT ON THE SAME wORKPIECE SIMUlTANEOUSlY.
Maintenance
instructions
• Occasionally apply a few drops of oil to the
rack toothing.
• The bearings of the feed shaft are self-
lubricating and must not be greased
• grease the sliding surface of the carriage
with MOlYCOTE grease.
• when not in use or being transported the
unit should be kept in the case supplied.
• After use ensure unit is clean of swarf and
dirt.
• Parts that are worn or damaged should
be replaced immediatley with genuine
manufacturer's replacements.
• Ensure all cutting edges are sharp when in
operation. Using blunt cutting tools may lead
to an overload of the motor.
• After every 30 minutes running, it is
recommended that the machine is laid on its
side to permit grease to run across the gear
train.
• After repeated use, the cradle may become
loose. This is remedied by adjusting the tension
screws on the side of the body. Put 2.5mm
hex wrench into head of cradle retaining nuts,
using 8mm Spanner undo the locking nuts
anti-clockwise, holding the hex wrench without
moving grub screws.
Using the hex wrench gently tighten screws in
series until the cradle moves freely in the slide
but does not allow the motor to wobble.
when adjustment is complete re-tighten
locking nuts clockwise, ensuring the grub
screws do not move from their new positions.
en
5