At The End Of The Work; Maintenance; Disposal; Troubleshooting - Hillyard Trident BP6V Manuel D'utilisation Et D'entretien

AT THE END OF THE WORK

1. Make sure the machine has been secured (see the section titled
2. Take the appliance to the designated place for emptying the tank.
3. Carry out the procedures described in the chapter "MAINTENANCE".
4. Position the appliance on a flat surface in an enclosed place; there must be no objects near the
appliance that could either damage it, or be damaged through contact with it. If you decide to hang the
appliance on supports, make sure they are able to sustain its volume and weight.

MAINTENANCE

1. Make sure the machine has been secured (see the section titled
2. Remove the vacuum nozzle (1) from the hole in the cover (2) of the appliance, turning it anti-clockwise
(Fig.1).
3. Remove the cover (2) from the vacuum tank (Fig.2), using the hooks (3) on the side of the tank itself
(Fig.3).
4. Remove the collection bag (4) from the tank (Fig.4). Change it if necessary.
2
1
1 2
N.B.: If fabric dust collection bags are used, instead of paper ones, empty them and clean
them with a jet of air, check their condition and change them if necessary.
5. Remove the fabric filter (5) from the appliance (Fig.5).
N.B.: If the surface of the filter is extremely dirty, brush the filter with a normal soft brush to clean it
thoroughly, and if necessary wash it in water.
ATTENTION: Check the condition of the cloth filter if the filter surface area is particularly clogged
or if it is damaged replace it.
6. Clean the inside of the collection tank with a damp cloth.
7. Insert the fabric filter (5) in the tank (Fig.6).
WARNING: Before inserting the fabric filter (5) in the tank, wait until it is completely dry if it was
previously washed.
ATTENTION: When inserting the fabric filter (5) into the tank, make sure that the gasket sticks
completely to the edge of the tank, so as not to compromise the vacuum being effective.
4 5
4 5
8. Insert the collection bag inside the collection tank (4) (Fig.7)
9. Put the cover (2) over the vacuum tank (Fig.8), securing it with the hooks (3) on the side of the tank
itself (Fig.9).
ATTENTION: When fitting the cover (2) make sure that the nozzle (6) in it fits correctly in the hole
in the collection bag (4) (Fig.8).
10. Disconnect the vacuum hose (6) from the cover (2) (Fig.10).
11. Clean the inside of the vacuum hose with a jet of compressed air, if necessary removing any
obstructions.
12. Disconnect the cleaning accessory.
13. Clean the inside of the vacuum chamber of the accessory with compressed air, and if necessary
remove any obstructions.
4 2
7 8
6
10
"APPLIANCE SAFETY"). To dispose of the appliance, take it to a demolition centre or an authorised
collection centre.
Before scrapping the machine it is necessary to remove and separate the
following materials and send them to the appropriate collection centres in
accordance with the environmental hygiene regulations currently in force:
• Felt
• Electric and electronic parts*
• Plastic parts
"APPLIANCE SAFETY").
• Metallic parts
(*) In particular, to scrap the electric and electronic parts, contact your area
distributor.
This chapter lists the most common problems linked with the use of the appliance. If you are unable to
resolve the problems with the information given here, please contact your nearest assistance centre.
3
PROBLEM
3
5
6
Manufacturer:
FIMAP S.p.A.
Via Invalidi del Lavoro, n°1
c.a.p. 37059 - S. Maria di Zevio (VR) - Verona - Italia
Tel. +39 045 6060411 - Fax. +39 045 6060417
E-mail:
Web:
Agent:
Hillyard, Inc.
302 North 4th Street - P.O. Box 909 - St. Joseph, Missouri 64501 USA
Phone: 1-800-365-1555 - Fax: 1-800-881-3840 - Web:
3
9
10

DISPOSAL

TROUBLESHOOTING

POSSIBLE CAUSE
The main switch is not activated.
The battery is not in the lower part of
the vacuum cleaner tank.
The battery is dead.
The battery charger does not charge
the battery, he electronic specifications
of the battery charger do not match
the electronic specifications of the
mains network.
The power cable of the battery
charger is damaged.
The vacuum hose is incorrectly
connected to the collection tank.
The vacuum hose is not connected
correctly to the telescopic tube.
The telescopic tube is not correctly
connected to the accessory that is
being used.
The vacuum circuit is blocked
(vacuum hose; telescopic tube;
vacuum accessory).
There is a blockage in the vacuum
filters.
fimap@fimap.com
www.fimap.com
SOLUTION
Place the main switch on "I".
Put the battery in the battery
compartment on the rear of the
appliance, making sure that the
battery poles are facing the top of the
appliance. Press the battery until the
clamp is in place.
Charge the battery, read the
paragraph "RECHARGING THE
BATTERY".
Check that the technical data on the
battery charger's rating plate match
the data of the mains power supply.
Contact a specialised technician
immediately and have it replaced.
Connect the vacuum hose correctly to
the collection tank.
Connect the vacuum hose correctly to
the telescopic tube.
Connect the accessory correctly to the
telescopic tube.
Remove the obstruction in the vacuum
circuit.
Clear the obstruction in the vacuum
filters.
www.hillyard.com