Maintenance - Wolf Garten SDE 2500 EVO Notice D'instruction D'origine

Working with the garden chopper
1
Wear protective gloves and hearing protection!
z Adopt a working position at the side of or behind the appliance.
Never stand in the area of the discharge opening.
z Never put your hands in the feed or discharge opening.
z Before switching on the appliance check whether there is any
chaff in the hopper.
z If foreign bodies should enter the hopper or should the appliance
make unusual noises or vibrations, switch the appliance off im-
mediately and allow it to come to a standstill. Remove the mains
plug and carry out the following:
–
Check the appliance and tighten any loose parts.
–
Replace damaged parts.
–
Repairs to the appliance must be performed by an authorised
service centre.
What can be chopped
z Organic waste from the house and garden e.g. hedge and tree
cuttings, dead flowers, kitchen scraps.
What cannot be chopped?
z Glass, metal parts, plastics, plastic bags, stones, material waste,
roots with earth, food, fish and meat waste
Switching on / off
Press the green button to switch on
z Press the red button to switch off
3
The machine has a circuit breaker to prevent switching
back on unintentionally after a power cut.

Maintenance

General
1
Remove the mains plug before any maintenance and
cleaning work!
When servicing the cutting tool ensure that it can still al-
ways run on even when the motor is switched off.
Wear protective gloves.
z Store the appliance in a dry location out of the reach of children.
General cleaning information
1
Remove the mains plug before any maintenance and
cleaning work!
z Handle the appliance with care and clean it regularly to prolong
its service life.
z Keep the ventilation slits clean and dust-free.
z Only use a warm and moist cloth to clean the appliance as well
as a soft brush.
z Do not allow the appliance to get wet and do not spray with water.
12
D
(2)
D (3)
Overload protection
3
An overloading of the appliance (e.g. culminating in the
blocking of the blades) can lead to the standstill of the ap-
pliance after a few seconds. To protect the motor from da-
mage the appliance is automatically disconnected from
the mains by the overload protection.
z Before putting into operation again wait for at least one mi-
nute before immediately pressing the reset button
and then ON/OFF switch. If the motor does not start, clean
the collection hopper (see Maintenance).
Special instructions for chopping
z Chop branches, twigs and wood shortly after cutting (this chop-
ped material will become very hard once it has dried out, therefo-
re the maximum diameter which can be processed is less).
z Remove the side shoots on severely ramified branches.
z When processing garden or kitchen waste with a high water con-
tent with a tendency to stick, crush alternately with wooden chop-
ping material to avoid blocking the appliance.
z Do not allow the chopping material in the area of the discharge
opening to accumulate too high. This can lead to material which
is already chopped blocking the discharge channel. This can
cause a kickback of the material through the filling opening.
z Ensure that the maximum branch diameter for processing permit-
ted for your appliance is observed.
z The blade unit pulls in the chopping material largely by itself.
z Do not overload or block the motor in the case of tough branches
by frequently pulling back the branch.
Cleaning the collection hopper
1
Remove the mains plug before any maintenance and
cleaning work!
1. Unscrew the knob and fold the casing upwards to open
2. Clean the cutting and discharge area of all objects which could
block the blades.
3. Close the casing again and tighten the knob
4. Press the reset button before activating the ON/OFF switch.
Safety locking device
z The chopper is equipped with a safety locking device at the lock
between the casing and the motor casing.
z In the event that the casing does not close flush to the motor ca-
sing, the motor is stopped by the safety locking device.
z In such a case, proceed as follows:
–
Unscrew the knob and fold the casing upwards to open
–
Carefully clean the contact surfaces.
–
Close the casing again and tighten the knob
D (1)
E .
E .
E
.
E
.
en