Renkforce 1530623 Mode D'emploi page 4

Operating instructions
Built-in HF motion detector
Item no. 1530623
Intended use
The motion detector's integrated HF sensor responds to motions within the detection range,
e.g., when a person enters the detection range. Thus, the motion detector can be used for
monitoring entrances or staircases.
The motion detector's output can be used, for example, for controlling a light or other power
consuming device. Observe the maximum connected load in the chapter „Technical data".
The motion detector is only intended for use in dry, closed interiors, it must not get damp or wet.
For safety and approval reasons, you may not convert and/or alter the product. If you use the
product for other purposes than those described above, the product may be damaged. Further-
more, an improper use involves risks such as short-circuits, fire, electric shocks, etc. Please
read the operating instructions carefully and do not discard them. If you pass the product on to
a third party, please hand over these operating instructions as well.
This product complies with the applicable national and European Regulations. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Package contents
• Motion detector
• Operating Instructions
Up-to-date operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the
QR code. Follow the instructions on the website..
Explanation of symbols
The lightning symbol inside a triangle is used when there is a potential risk of per-
sonal injury, such as electric shock.
An exclamation mark in a triangle indicates important instructions in these operating
instructions which absolutely have to be observed.
The arrow symbol is used when specific tips and information on the operation are
provided.
The product is only intended to be installed and used in dry indoor spaces; it must
not get damp or wet.
Observe the operating instructions!
Safety instructions
Please read the operating instructions carefully and pay particular attention
to the safety instructions. We do not assume liability for any injuries/mate-
rial damages resulting from failure to observe the safety instructions and the
information in these operating instructions regarding the proper use of the
product. Furthermore, in such cases, the warranty/guarantee will be null and
void.
Attention, important note!
Only persons with relevant electro-technical knowledge and experience
should carry out the installation! *)
If it is not installed properly, you risk:
• your own life
• the life of the person using the electrical system.
If it is not installed properly, you risk severe damage to property, e.g., by fire.
You face the risk of being held liable for personal injury and material damage.
Contact an Electrician!
*) Specialist knowledge required for the installation:
In particular, the following expertise is required in regards to the installation:
• the applicable „5 safety rules": Switch off power; secure against switching back
on; determine voltage-free status; earthing and short-circuiting; cover or fence off
nearby live parts
• Choose appropriate tools, meters and, if necessary, personal protective equip-
ment
• Evaluation of the measurement results
• Selection of the electrical installation material to ensure the shutdown conditions
• IP protection types
• Installation of the electrical installation material
• Type of mains supply network (TN system, IT system, TT system) and the con-
nection conditions that follow from them (classical earthing, protective earthing,
required additional measures, etc.)
If you do not have the expertise required for the installation, do not connect
and install it yourself, but ask a qualified technician.
• Unauthorised conversion and/or modification of the product is not allowed for
safety and approval reasons. Do not open/disassemble. It does not contain any
internal parts that need to be adjusted or maintained by you.
• Maintenance, adjustment or repair work may only be carried out by an expert/
authorised service centre familiar with the hazards involved and the relevant regu-
lations.
• The motion detector is not a toy and should be kept out of the reach of children!
There is a risk of fatal electric shock! Install the motion detector out of the reach
of children.
• The product may only run on mains voltage (see section „Technical data"). Never
try to operate the product at another voltage, as this will ruin the product.
• During installation, all poles must be disconnected from the mains voltage, e.g.,
via RCD. There must be an appropriately dimensioned fuse or circuit breaker be-
tween the RCD and the product.
• The product may be installed and used only in dry indoor spaces; it must not get
damp or wet. There is a risk of fatal electric shock!
• Only use the product when it is firmly mounted/steady. Never install and/or operate
it in vehicles.
• Do not use the product in rooms with adverse environmental conditions, where
combustible gases, vapours or dust are or may be present! There is a danger of
explosion!
• Do not expose the product to extreme temperatures, strong vibrations or strong
mechanical stress.
• Do not connect the product to the power supply immediately after it has been
transferred from a cold room into a warm one (e.g., during transport). The conden-
sation that forms might destroy the device. Moreover, there is danger of electric
shock!
Allow the product to reach room temperature. Wait until the condensation has
evaporated. This might take several hours. Only after this, should it be installed,
connected to the mains supply and put into use.
• If it can be assumed that safe operation is no longer possible, the product must be
turned off and precautions are to be taken to ensure that it is not used unintention-
ally. Do not touch the product.
First switch off the mains voltage to all poles (switch off the connected circuit
breaker or remove the fuse and then switch off the connected RCD).
After this, arrange for a skilled electrician to check the product.
• Safe operation can no longer be assumed if:
- the product shows visible signs of damage
- the product does not work at all or well (flickering light, leaking smoke or a smell
of burning, the light flickers, audible cracking noises, discolouration to the prod-
uct or the adjacent surfaces.)
- the device was stored for a longer period of time in unfavourable conditions
- it was exposed to heavy loads during transport
• Do not leave the packaging material carelessly lying around, since it could be-
come a dangerous plaything for children.
• On industrial sites, the accident prevention regulations of the association of the
industrial workers' society for electrical equipment and utilities must be followed!
• If you have any questions that are not answered in this manual, please contact our
technical service or another specialist.