Brightness Control - Makita DMR104 Manuel D'instructions

Storing stations in preset memories (DAB
and FM)
There are 5 memory presets for each waveband.
1. Press the Power button to turn on the radio.
2. Tune to the desired station using one of the methods
previously described.
3. Press and hold the desired Preset button until the
preset number shown on the display, for example, "P2
Saved". The station is then stored in the selected
Preset button.
4. Repeat this procedure for the remaining presets.
5. Stations stored in the preset memories can be
overwritten by following the procedures described
above.
Recall stations from the preset memories
(DAB and FM)
1. Press the Power button to turn on the radio.
2. Press the Band button to select your desired
waveband.
3. Press the desired Preset button momentarily. The
preset number and station frequency will appear in the
display.
Language options (only available in
DMR105)
There are four language options available in the radio:
English, German, Italian and French.
1. Press Advanced setting button.
2. Rotate the Volume/Tuning Control/Select knob until
"Language" shown on the display. Press the Volume/
Tuning Control/Select knob to enter the setting.
3. Rotate the Volume/Tuning Control/Select knob to
choose your desired language. Press the Volume/
Tuning Control/Select knob to confirm your setting.

Brightness control

The backlight of the display can be adjusted.
1. Press the Advanced setting button.
2. Rotate the Volume/Tuning Control/Select knob until
"Backlight" shown on the display. Press the Volume/
Tuning Control/Select knob to enter the setting.
3. Rotate the Volume/Tuning Control/Select knob to
choose to enable or disable the backlight function,
then press the Volume/Tuning Control/Select knob to
confirm the setting.
System reset
If your radio fails to work correctly, or some digits on the
display are missing or incomplete, carry out the following
procedure.
1. Press the Advanced setting button.
2. Rotate the Volume/Tuning Control/Select knob until
"Factory Reset" shown on the display. Press the
Volume/Tuning Control/Select knob to enter the
setting.
10
3. Rotate the Volume/Tuning Control/Select knob to
choose "Yes". Press the Volume/Tuning Control/Select
knob to confirm the setting and a full reset will be
performed.
Software version
1. Press the Advanced setting button.
2. Rotate the Volume/Tuning Control/Select knob until
"SW Version" shown on the display. Press the Volume/
Tuning Control/Select knob to view the software
version installed in the radio.
Micro USB port for software upgrade
Software updates for your radio may be available in the
future.
As software updates become available software and
information on how to update your radio can be found at
Makita website.
How to play other audios
CAUTION:
Unplug this apparatus before connecting other audios.
• There are 2 AUX IN sockets. AUX IN 1 is located on
the front panel, and AUX IN 2 is located in the battery
compartment.
• Connect a stereo or mono source (i.e. iPod, MP3, or
CD player) to either AUX IN 1 or AUX IN 2 by audio
cord.
• Repeatedly press and release the Band button until
"AU1" or "AU2" is displayed, then AUX function is
activated.
MAINTENANCE
CAUTION:
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Specifications:
Power requirements
AC power adaptor DC12 V 1A, center pin positive
Battery Cluster battery: 7.2 V - 18 V
Slide battery: 9.6 V - 18 V
Frequency coverage FM 87.50 - 108 MHz
DAB/DAB+ 174.928 - 239.200 MHz
DAB/DAB+ Channel block
DAB (Band III) 5A-13F
Compatible standard DAB (DMR104)
DAB/DAB+ (DMR105)
Circuit feature
Loudspeaker 3 inches 8 ohm
Output power 7.2 V: 0.5 W x 2, 9.6 V: 1 W x 2
10.8 V: 1.2 W x 2, 12 V: 1.5 W x 2
14.4 V: 2.2 W x 2, 18 V: 3.5 W x 2
Input terminal 3.5 mm dia. (AUX IN1/AUX IN2)
Antenna system DAB/FM: soft bended rod antenna
Dimension (W x H x D) in mm
280 x 302 x 163
Weight 4 kg (without battery)