Before Starting The Equipment - Pattfield Ergo Tools PE-AA 18 Li Basic Traduction De La Notice Originale

in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Changing the saw blade (Fig. 3a)
Warning!
Switch off the universal saw and pull out the bat-
tery pack each time before doing any work on the
machine and changing the blade.
Open the cover (Fig. 3a/Item A) by pressing it to-
gether slightly at the front and then swinging it up.
Turn the ring (B) on the blade holder (4) as shown
in Fig. 3a until the blade (6) lets itself be slipped
Anl_PE_AA_18_Li_Basic_SPK7.indb 114 Anl_PE_AA_18_Li_Basic_SPK7.indb 114
GB
into the slot of the blade holder (4). When you now
let go of the ring (B) again, the ring (B) should
return to its starting position. If this fails to happen,
try turning the ring (B) by hand into its starting
position.
Now pull on the blade to check whether it is tightly
seated in the holder.
5.2 Fitting the branch jaw clamp (Fig. 3b/3c)
The branch jaw clamp (Fig. 1/Item 5) helps you to
guide the equipment when cutting branches. The
equipment can be used either with or without the
branch jaw clamp.
To fi t the branch jaw clamp, press the lock release
(Fig. 3b/Item A) and push the branch jaw clamp
onto the soleplate from above. Make sure that the
two pins (Fig. 3c/Item A) are correctly seated in
the related recesses (Fig. 3c/Item B) of the so-
leplate. Then check that the branch jaw clamp is
securely seated.
5.3 Charging the Li battery pack (Fig. 4-5)
1. Remove the battery pack (A) from the handle,
pressing the pushlock button (B) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(C) into the socket outlet. The green LED will
then begin to blink.
3. 3Insert the battery pack (7) into the battery
charger (8).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit.
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
•
to our customer service center.
- 114 -
24.11.2017 09:29:03 24.11.2017 09:29:03