Set Up An Internet Access Point For Packet Data (Gprs); Advanced Internet Access Point Settings For Packet Data (Gprs); Ip Passthrough; Set Up A Data Cable To Use Ip Passthrough - Nokia E62 Guide D'utilisation

C o n n e c t i v i t y
Login script — Enter the login script. This setting is available only if you have selected
•
Modem initialisation — Enter a command string for the connection setup, if required by your service provider.
•

Set up an Internet access point for packet data (GPRS)

1. Select Menu Tools
> >
2. Select Options New access
>
start with an empty access point, select
3. Define the following settings.
Connection name — Enter a descriptive name for the connection.
•
Data bearer — Select
•
Access point name — Enter the name for the access point. The name is usually provided by your service provider or network
•
operator.
User name — Enter your user name if required by the service provider. User names are often case-sensitive and provided
•
by your service provider.
Prompt password — Select
•
device memory and automate the login.
Password — Enter your password if required by the service provider. The password is often case-sensitive provided by
•
the service provider.
Authentication — Select
•
when possible.
Homepage — Enter the Web address of the page you want to display as a home page when you use this access point.
•
4. After defining the settings, select
and exit.

Advanced Internet access point settings for packet data (GPRS)

After setting up a basic Internet access point for packet data (GPRS), select
advanced settings:
Network type — Select
•
and from your device.
Phone IP address — Enter the IP address of your device. Select
•
This setting is shown only if you select
DNS address — Enter the IP addresses of the
•
or network operator. Otherwise, the name server addresses are provided automatically.
Proxy serv. address — Enter the address of the proxy server. Proxy servers are intermediate servers between a browsing
•
service and its users, which are used by some service providers. These servers may provide additional security and speed up
access to the service.

IP passthrough

Select Menu Connect.
> >
The IP passthrough application allows you to obtain a network connection on your device from a compatible PC through a data
cable.

Set up a data cable to use IP passthrough

Use IP passthrough as you use any Internet access point to browse or synchronize remotely. If a wireless network connection
is unavailable, use IP passthrough to access the Internet. You cannot use IP passthrough at the same time as Nokia PC Suite.
You cannot activate the modem if you select IP passthrough in cable connection settings.
To prepare for an IP passthrough session, connect a data cable to your device, and select
method. Connect the other end of the data cable to a compatible PC, and wait for the PC to recognize your device.

Access point for IP passthrough

Menu Tools Settings
> > >
To configure IP passthrough basic settings, select
passthrough connection in the

Advanced IP passthrough access point settings

Menu Tools Settings
> > >
To use advanced settings, open an IP passthrough access point, and select
following:
Copyright © 2006 Nokia. All Rights Reserved.
Settings Connection Access
> >
point. To use an existing access point as a basis for the new one, select
Use default
Packet data.
Yes to enter your password each time you log into a server or
Secure to always send your password encrypted or
Options Advanced settings
>
IPv4 or IPv6 as the Internet protocol type. The Internet protocol defines how data is transferred to
Network type
Primary DNS address
Data cable Options IP
> >
Connection Access points.
>
Options
Connection name field, and select
Connection Access points.
>
points.
settings.
to define the advanced settings or
Options
Automatic to have the network provide the device IP address.
> IPv4.
and Secondary DNS addr.
passthrough.
New access point
>
IP passthrough
Options
70
Use login script
Use existing
No to save the password in your
Normal to send your password encrypted
Back
Advanced settings, and define the following
>
if required by your service provider
IP passthrough
Use default settings. Enter a name for your IP
>
in the Data bearer field.
Advanced settings
>
> Yes.
settings. To
to save the settings
as the connection
and select from the