Mode Key Ir Punch-Through; Resetting The Cr104; Command Summary; Device Codes - Arcam rmj BDP100 Manuel

Mode key iR punch-through

The Mode key Ir punch-through default is 'on' .
example: To set the Mode key iR punch-
through to aMP
Press and hold S until the power LED blinks
1.
twice: * * .
Press 9 7 1 . The power LED blinks twice:
2.
* * .
Press A to punch through Ir from it.
3.
now, whenever you press and release a Mode key, the
Ir data assigned to is transmitted, no matter what
aMP
the current mode is (i.e. it 'punches through' any other
device).
To cancel Mode key iR punch-through
Press and hold S until the power LED blinks
1.
twice: * * .
Press 9 7 1 . The power LED blinks twice:
2.
* * .
Press S until the power LED blinks twice: *
3.
* .

Resetting the cR104

resetting the Cr104 will erase all learned functions
across all modes, as well as some other programmed
functions like Macros. It will not reset the Device Mode
keys; these will remain programmed to your choice of
component.
Press and hold S until the power LED blinks
1.
twice: * * .
Press 9 8 0 . The power LED blinks four
2.
times: * * * * .
Press and hold S until the power LED blinks
3.
twice: * * .
Press 9 9 3 .
4.
Press A . The power key LED blinks twice: *
5.
* .
Press and hold S until the power LED blinks
6.
twice: * * .
Press 9 7 1 . The power LED blinks twice:
7.
* * .
Press A . The power key LED blinks twice: *
8.
* .

Command summary

direct code setup
(e.g. AV mode, nnnn=code number)
a S * * nnnn * * P
library search
(e.g. AV mode)
a S 9 9 1 * * P [ until unit turns off
S to save
code blink back
a S 9 9 0 **
1 count blinks for first N
2 count blinks for second N
3 count blinks for third N
4 count blinks for fourth N
code learning
(e.g. AV mode fast forward key)
S * * 9 7 5 * * a ( * (many
rapid blinks)
(Press key on original remote that you wish to copy)
* * S * *
delete a learned function
(e.g. AV mode fast forward key)
S * * 9 7 5 * * a ( ( * *
delete all learned functions with a device
(e.g. AV mode)
S * * 9 7 5 a a
creating macros
(e.g. SrCH key)
S * * 9 9 5 h a P w P z P S
* *
deassign macro
S * * 9 9 5 h S * *
key mover
(e.g. SAT mode, DISP key to MEnU key)
z S * * 9 9 4 D U
Mode mover
(e.g. change SAT to TV(AV))
S * * 9 9 2 a z
Restore device mode
(e.g. restore SAT)
S * * 9 9 2 z z
locking/unlocking a mode
(e.g. CD mode)
c S * * 9 8 2 * *
(i.e. two blinks for lock)
c S * * 9 8 2 * * * *
(i.e. four blinks for unlock)
cancel all volume punch-through
S * * 9 9 3 + * * * *
Restore volume punch-through
S * * 9 9 3 A * *
Mode key iR punch-through
S * * 9 7 1 * * A
cancel mode key iR punch-through
S * * 9 7 1 * * S * *
NOTE
As elsewhere in this Handbook, a single 'blink' of
the red LED behind the power button is indicated
by the symbol * .
e-29

Device codes

The tables that begin on page C-1 (in the final section of
this Handbook) list the four-figure codes for different
manufacturers' devices.
Use these when setting your Cr104 up to control your
devices, as described in Method 1 (see page E-15).
If more than one code number is listed, try the first
number. If the results are unsatisfactory, continue trying
the numbers for that manufacturer to get the best 'fit'
with the functionality required.
If the manufacturer of your equipment is not listed, you
can try Method 2, the Library Search (see page E-15). This
allows you to scan through every set of codes contained
in the Cr104's memory.