Battery Installation - Makita DMR107 Manuel D'instructions

5. Preset stations
6. Scan tuning and Time set
7. Tuning/Volume control knob
8. DC IN socket
9. Input terminal (AUX IN1)
10. Soft bended rod antenna
11. Battery compartment (covering main battery pack and
back up batteries)
12. Handle
13. Speaker
14. Battery compartment locker
15. Main battery compartment
16. Back up battery compartment
17. Red indicator
18. Button
19. Battery cartridge
20. Input terminal (AUX IN2)
21. Front
22. Right
23. Back; Battery cover closed
24. Back; Battery cover opened
25. Indicator lamps
26. Check button
LCD display:
A. Radio alarm
B. HWS buzzer alarm
C. Scan tuning
D. Band Indicator
E. Low battery indicator
F. Preset stations
G. Sleep and Snooze status
H. Frequency
I. Stereo symbol and Volume
J. Clock
K. Time set
L. PM for clock

Battery installation

Note:
Keeping back up batteries inside the compartment
prevent stored data in preset memories from being lost.
Back up battery installation
1. Pull out the battery compartment locker to release
battery compartment. There are main battery pack
compartment and back up battery compartment.
(Fig. 2 & 3)
2. Remove back up battery compartment cover and
insert 2 fresh UM-3 (AA sizes). Make sure the
batteries are with correct polarity as shown inside the
compartment. Replace the battery cover.
3. After back up batteries are inserted, insert the main
battery pack to power radio. The suitable battery
packs for this radio listed as the following table.
The following tables indicate the operating time on a
single charge.
6
Battery Cartridge Voltage
Battery
capacity
7.2 V 10.8 V
1.0 Ah BL7010
BL1013
1.3 Ah
BL1015
1.5 Ah
BL1020B
2.0 Ah
3.0 Ah
BL1040B
4.0 Ah
5.0 Ah
6.0 Ah
: Cluster Battery
: Slide Battery
Note:
Table regarding to the battery operating time above is for
reference. The actual operating time may differ with the
type of the battery, charging condition, or usage
environment.
Installing or removing Slide battery
cartridge (Fig. 4 & 5)
• To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click.
• If you can see the red indicator on the upper side of the
button, it is not locked completely. Install it fully until the
red indicator cannot be seen. If not, it may accidentally
fall out of the tool, causing injury to you or someone
around you.
• Do not use force when installing the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
• To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge or
pressing the buttons on both sides of the cartridge.
Installing or removing Cluster battery
cartridge (Fig. 6 & 7)
• Pull the supporting bar to allow the battery to insert to
the terminal.
• To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place.
• Release the supporting bar.
At speaker
output =
50 mW + 50 mW
14.4 V 18 V
(Unit: Hour)
(Approximately)
8.5
BL1415 BL1815
9.5
BL1415N BL1815N 10
13
BL1820/
14
BL1820B
BL1430 20
BL1830/
21
BL1830B
26
BL1440 27
BL1840/
28
BL1840B
BL1450 34
BL1850/
35
BL1850B
BL1860B 42
7
9