Technical Specifications - Nice Era Star T Instructions Et Avertissements Pour L'installation Et L'utilisation

5.9 - Deleting the entire memory
Caution! - This procedure deletes all data in the Con trol unit memory, including positions "0" and "1".
01. Use the Up or Down button to move the awning to the point of mid-travel.
02. Press and hold the Up and Down buttons simultaneously and wait for the awning to perform a short movement, after which release only one of the two buttons
03. With 3 seconds after the awning has performed the short movement, press the previously released button (in point 02) three times.
04. The release the other pushbutton.
Note – If cancellation is completed correctly, on activation of an up or down command, the awning will perform two short movements (= no limit position programmed).
01 02
WARNINGS FOR DAILY USE OF
6
THE AUTOMATION
6.1 - Maximum continuous work cycle
In general the tubular motors in the "Max" range, while guaranteeing a maximum
continuous use of 4 minutes, are designed for residential applications and therefore
for discontinuous use. Therefore in the event of overheating (for example due to con-
tinuous and prolonged activation ) a thermal cut-out trips automatically to shut off
power supply. Power is only restored when the temperature returns to within the nor-
mal range.
What to do if ...
(troubleshooting guide)
q When an electric phase is powered, the motor does not move:
Unless a thermal cut-out has tripped, in which case it is sufficient to wait for the
motor to cool, check that the mains power voltage corresponds to the data stat-
ed in the technical specifications in this manual, measuring the energy between
the "common" wire and that of the powered electric wire. Then try and power the
opposite electric phase.
q When an up command is made, the motor does not start:
If the awning is already closed or nearly closed, the motor does not perform the
up manoeuvre. In this case move the awning down slightly and then repeat the
up command.
q The system operates in emergency hold-to-run conditions
– Check whether the motor has been subject to a severe electrical or mechanical
shock.
– Check that all motors components are intact.
– Perform the deletion procedure (paragraph 5.9) and programme the limit
switches again.
Disposal of the product
This product constitutes an integral part of the automation system, therefore it
must be disposed of along with it.
As in installation, also at the end of product lifetime, the disassembly and scrapping
operations must be performed by qualified personnel.
This product is made up of different types of material, some of which can be recycled
while others must be disposed of. Seek information on the recycling and disposal
systems envisaged by the local regulations in your area for this product category.
Caution! - some parts of the product may contain pollutant or hazardous sub-
stances which, if disposed of into the environment, may cause serious damage to
the environment or physical health.
As indicated by the symbol on the left, disposal of this product in
domestic waste is strictly prohibited. Separate the waste into cate-
gories for disposal, ac cording to the methods envisaged by current
legislation in your area, or return the product to the retailer when pur-
chasing a new version.
Caution! - Local legislation may envisage serious fines in the event of abusive dis-
posal of this product.
8 – English
03
1
Power supply voltage: 230 Vac - 50 Hz
Power absorption on standby: 0,5 W
Encoder resolution: 2,7°
Continuous operation time: 4 min
Connection cable length: 2,5 m
Operating temperature: -20°C
IP Protection rating: IP 44
Note:
– All technical characteristics refer to an ambient temperature of 20°C (± 5°C).
– Nice S.p.a. reserves the right to apply modifications to the product at any ti -
me when deemed necessary, while maintaining the same functionalities and
in tended use.
Nice S.p.A. hereby declares that the products: E Star ST 324, E Star ST 524,
E Star ST 611, E Star ST 1011, E Star ST 430, E Star MT 1030, E Star MT
817, E Star MT 1517, E Star MT 3017, E Star MT 4012, E Star MT 5012 com-
ply with the essential requirements and other relevant provisions as established
by the directives 2006/95/EC, 2004/108/EC. The EC declaration of conformity
can be consulted and printed out at the web site www.nice-ser vice.it or may be
requested from Nice S.p.A.
04
x 3
THE
END
Technical specifications
EC declaration of conformity
Ing. Luigi Paro
(Managing Director)