Editing Screwing Parameters; Erasing Screwing Parameters; Transfer Of Screwing Parameters To Draft; Screwing Parameter Work Schedule Draft Field - Bosch CRR 320 Consignes D'utilisation

en 40 | CRR 320 | Work schedule editor
Item Designation Description
1 Measure- The measurement mode with which
ment mode the screwing operation is performed.
2 ID number input Is an identification number to be as-
signed to the screwing operation?
The options for selection are No-
ne, Keypad (optional) and Bar code
scanner (optional). If the wrench
has the corresponding functions, the
identification number input mask
appears in the wrench display in
front of the screwing operation.
3 Allow NOK Yes: NOK screwing operations are
tightening included in the repetition count
and are not to be repeated.
No: NOK screwing operations are
not included in the repetition count.
4 Repetitions Number of times this screw-
ing parameter set must be re-
peated until it is completed.
5 Cancel Closes the window without crea-
ting a new screwing parame-
ter data record. Values en-
tered are not retained.
6 Accept Creates a new screwing parameter
data record with the values entered.
7 Description Description of the screwing para-
meter set. This description is dis-
played on the wrench on para-
meter selection. The two input
boxes represent the two display li-
nes of the wrench. Each input box
has capacity for 20 characters.
8 Gauge dimen- Distance between the center of
sion [mm] rotation of the attachment used
for this screwing operation and
the end of the attachment hol-
der of the wrench in mm.
9 Unit Unit of the torque values displayed.
10 Threshold value Torque value as of which measu-
rement recording commences.
Can be used to specify the start
of curve plotting as of a certain
point in the screwing operation.
23.3

Editing screwing parameters

1. Select the screwing parameter line in the database
table by clicking onto the corresponding header.
2. Click onto the button (Fig. 14, Pos. 2) Edit screwing
parameters
The window which opens is the same as when creating
a new screwing parameter. The difference is that the
values for the parameter selected are written into the
boxes.
If there is a link with the wrench, the values to be edi-
ted are checked for compatibility with the connected
wrench. If any values are not compatible, standard valu-
es are set instead. Such substitution of standard values
is indicated by a
|
0 986 629 502 2015-02-16
23.4

Erasing screwing parameters

All data records selected in the database table are irre-
vocably erased from the database. As an alternative to
using button (3), the screwing parameters selected can
also be erased by way of the Remove menu item of the
context menu.
23.5 Transfer of screwing parameters to
draft
There are two options for transferring screwing parame-
ters from the database table to a draft.
Drag & drop
1. Mark the line.
2. "Grasp hold" of the header of the marked line with
the mouse pointer (press and hold the left mouse
key).
3. With the left mouse key pressed, move the cursor
over the position in the work schedule at which the
parameter set is to be inserted.
4. Release the left mouse key.
i
If the key is released over the draft table view at a
point where there is as yet no line, or if the draft
schedule is still blank, the screwing parameter will
be added at the end. Only one line can be transfer-
red to the schedule at a time using this method.
Context menu
1. Mark as many lines as required in the Database
table.
2. Call up the context menu with a right mouse click.
3. Click onto the menu item Add to draft.
The data records selected are then added to the end of
the draft.
23.6 Screwing parameter work schedule
draft field
Fig. 16:

Screwing parameter work schedule draft field

1) Load Bosch work schedule
2) Load work schedule
3) Save work schedule
4) Transfer work schedule
Robert Bosch GmbH