Remaining Hazards; Product Specifications; Technical Data - F.F. Group SCMS 254 PLUS Notice Originale

SCMS 254 PLUS
position. Do not work on items that are too small
to securely clamp in place.
Check for correct alignment of moving and rotat-
ing parts or other failures that could be a source
of danger. A damaged guard or other part should
be replaced by an authorized service center be-
fore operating the machine.
Do not touch the rotating parts before they come
in complete stop.
NOISE AND VIBRATION HAZARDS
The noise levels shown in these instructions are
the maximum levels for use of the machine. Insuf-
ficient maintenance has a significant impact on
vibration and noise emissions. Consequently, it
is necessary to take preventive steps to eliminate
possible damage due to high levels of noise and
stress from vibration. Maintain the machine well,
wear ear protection devices, anti-vibration gloves
and take breaks while working.
WORKING AREA HAZARDS
Thoroughly inspect the whole work area and use
a rake or yard brush to manually loosen debris
and remove anything that could be a hazardous
source to you or cause damage to the machine.
Keep work area clean and tidy. Do not operate the
machine in wet environment conditions or when
the machine itself is wet. Keep the machine away
from flammable material. Check that there are no
bystanders, animal or items that could be dam-
aged within the machine's range of action.
Operate only in well ventilated areas. Wood chips
and saw dust can be a health hazard when inhaled
or when in contact with the eyes. Always wear
appropriate half-mask respirator and protective
goggles, when working with such materials and
use a dust extraction device.
Work only in daylight, or with suitable artificial
light, in good visibility conditions. Try not to cause
any noise disturbance, by only using this machine
at reasonable times of the day.
Take on a firm and well-balanced position. Where
possible, avoid working on wet, slippery ground
or in any case on uneven or steep ground that
does not guarantee stability for the operator.
Storing of tools that are not in use should be done
in a dry and safe place away from the operating
machine and out of the reach of children.

REMAINING HAZARDS

The machine was built using modern technology
and in accordance with recognized safety rules.
Even when all safety measures are in place, some
remaining hazards, which are not yet evident, may
be present. The operator should use common
sense and take necessary precautions to avoid risk
due to remaining hazards.

PRODUCT SPECIFICATIONS

INTENDED USE
This machine is designed and manufactured for ma-
chining work pieces by cutting e.g. wood material
pieces. It is not designed for heavy commercial use.
Any other use differing from the above-mentio-
ned ones could be hazardous, harm people and/or
damage things and the machine itself.
IMPROPER USE
The machine must not be used for machining ha-
zardous materials, e.g. accumulation of inflam-
mable or explosive products and any other object
that could be dangerous to the machine itself as
well as the operator, bystanders, animals or pro-
perty.
Other examples of improper use may include, but
are not limited, to operation of the machine:
Without the original accessories supplied by the
f
manufacturer.
With original accessories but in a way not in accor-
f
dance to the instructions.
Without original spare parts.
f
With unauthorized modifications.
f
NOTE
According to the applicable product liability laws,
the manufacturer of the device does not assume lia-
bility for damages to the product or damages caused
by the product that occurs due to:
Improper handling no complied with the operat-
f
ing instructions.
Repairs by third parties and not by authorized ser-
f
vice technicians.
Installation of non-original spare parts.
f
Non-intended use.
f
Electrical system breakdown due to power of the
f
machine in a manner not compliant with the elec-
tric and VDE regulations.

TECHNICAL DATA

Article Number
Model
Rated voltage
Rated frequency
Power
No load speed
Blade outer
diameter
Blade bore size
Width of cut
Minimum workpiece
dimensions
(L x W x H)
Maximum cutting
capacity Mitre 0⁰ /
Bevel 0⁰
Maximum cutting
capacity Mitre 0⁰ /
Bevel 45⁰
English | 11
46 613
SCMS 254 PLUS
V 220-240
Hz 50
W 2.000
rpm 4.800
mm 254
mm 30
mm 2
mm 130 x 35 x 2,5
mm 90 x 300
mm 58 x 300
www.ffgroup-tools.com