Technical Details - Eurosystems Slalom67 Notice D'instructions Et Mode D'emploi

G
B
1 Seat
2 Steering wheel
3 Grass catcher bag
4 Blade
5 Ignition key
Electric starter
Advance
Maximun speed
Grass collection bin
Body
Cutting plate
Cutting width
Cutting height regulation
Curvature radius
Grass collection bag
Tyres
front
rear
Weight with collection bag
Assembled with
Acoustic power value according to
Directive 2000/14/CE
Acoustic pression power accor-
ding to Appendix H from regula-
tions En836
Vibrations value according to
Appendix G from regulations
En 836
PETROL MOWER WORKING HOURS
Monday to Saturday
Show respect for those living nearby and avoid using in afternoon rest period, evening or Sundays.
The grass collection sack is included in all the models of the ride-on-mower as a
standard accessory.
For assembly, you need the following parts:
- 1 Frame (1)
- 2 Hexagonal screws (M6x16) (7)
- 2 Washers Ø 6,5x24 (8)
- 2 self-locking nuts (M6) (9)
- 1 Fabric sack with clips
- 2 Z-shaped plates (4)
1. Mount the front wheels on the pins (1), positioning a washer (2), the wheel (3) and
2 washers (4).
2. Secure with a stop (5).
UNPACKING/ ASSEMBLY
The ride-on-mower is packed in a carton and is ready assembled apart from the steer-
ing wheel, seat, grass collection bin and front wheels. Please observe the following
sequence when unpacking the machine:
1. Unpack all the parts that have been delivered. Dispose of the carton and pallet in
an environmentally friendly way.
2. Check all the parts
3. Begin assembly.
It is strictly forbidden to start the ride-on-mower (even for trial purposes)
without completing assembly.
STEERING WHEEL ASSEMBLY
1. Fix the steering wheel (2) pulling until it is connected with the steering column (1).
2. Secure the steering wheel (2) by means of the socket pin (3); put the socket pin
through the openings (at the steering column and steering wheel)
The openings at the steering wheel and at the steering column must be in
exact alignment.
Before the cutting height is adjusted, the engine must be switched off and
the blades must have come to complete standstill.
ADJUSTMENT
1. Push the adjustment lever (5) outwards in order to release it from its seat.
2. Push the lever into the required notch for the cutting height.
3. Release the lever slowly till it sticks in the notch.
The cutting height is now set.
2 - DESCRIPTION
6 Throttle lever
7 Battery
8 Blade coupling lever
9 Brake pedal
10 Brake lever

3 - TECHNICAL DETAILS

Mod. 67
Hydrostatic advance forward and back
67 cm
Centralised on 5 positions
Height
265 mm
360 mm
Steering wheel, grass collection bag, front wheels and bin cover
LWA = 96,6 dBA
L eq (dBA) = 82,5
Seat = 2,77 m/s
Steering wheel = 2,52 m/s
08.00 - 12.00 h / 15.00 - 19.00 h
4 - ASSEMBLY OF THE GRASS COLLECTION SACK
5 - FRONT WHEEL ASSEMBLY
6 - ASSEMBLY
7 - ADJUSTING THE CUTTING HEIGHT
16
(Fig.1)
Electric
8,0 Km/h
2000 mm x 820 mm x 1020 mm
Polypropylene
Sheet steel
Centralised on 4 positions
0,7 m
150 litri
Width
85 mm
120 mm
177 kg
L eq (dBA) = 83,1
2
Seat = 3,25 m/s
2
Steering wheel = 2,77 m/s
(Fig.2-3)
- 1 Bar (3)
- 2 Self-locking nuts (M8) (6)
- 4 Washers Ø 9x24 (5)
- 2 Plugs Ø 5x50
1- Allow the sack to slide on the frame and secure with suitable clips.
2- Fix the bar with the 4 washers 9x24 (two before and two after the fabric sack) and
with the 2 M8 nuts.
(Fig.4)
Attention: Assemble the wheel with valve outwards
(Fig. 5-17)
SEAT ASSEMBLY
1- Fasten the seat (4) to the support plate (5) through the 4 M8x18 screws. Assembly
with 4 washers Ø 9x24 and 4 groovers.
2- Before tightening the screws, adjust the position of the seat on the holes of the plate
according to the user's needs.
Check at regular intervals that the nuts are tightly screwed down.
ASSEMBLY OF THE GRASS COLLECTION SACK
1.Fasten the bin to the rear part of the ride-on-mower with the 2 H.H. 6x16.2 screws,
the 2 Z-shaped plates and 2 M6 nuts.
2. Fix the bin cover to the engine casing inserting the two Ø 5x50 plugs
PLATE ASSEMBLY FOR FULL GRASS-BAG DETECTION
1. Insert the plate (12) into the slot (13).
(Fig.6-7)
EMPTYING THE GRASS COLLECTION BIN
Empty the grass collection bin in time before it overflows.
The orange light shows that the bin is full.
Don't go on filling the grass collection bin when the orange light situated
under the steering wheel is on.
Switch off the engine.
1. Hold the rod and swivel the bin. Shake the sack twice until it is completely empty.
2. Let the grass collection sack return slowly to its original position.
3. Switch on the engine.
11 Drive pedal
12 Agjusting levers for cutting height
13 Motor safety houding
14 Pilot light for check-in and for full grass
collection bin
15 Protection casing battery/engine
Mod. 76
76 cm
Recommended pressure
1,5 bar
2 bar
LWA = 98 dBA
2
2