KIKKA BOO HAPPY 2 Mode D'emploi page 5

WARNINGS
BEFORE USE CAREFULLY READ THESE INSTRUCTIONS. FAILURE TO OBSERVE THESE INSTRUCTIONS MAY AFFECT THE SAFETY OF YOUR CHILD
• It is intended for children from birth up to a maximum weight of 15kgs. . This stroller is designed for two children only. Total combined weight of 30kg maximum.
• The maximum loading carried in the basket must never exceed 3 kgs.
• lt may be dangerous to leave your child unattended . You are personally responsible for your child's safety.
• Ensure that all the locking devices are xed properly before use.
• Any load hung on the handlebar will a ect the stability of the stroller.
• Do not put things on the canopy. It may cause the stroller unbalanced and tip over.
• Prevent your child from falling and sliding out. Always use safety harness provided.
• This stroller isn't suitable for running or skating.
• Do not lift and carry the stroller while your child is seated.
• Do not use accessories that haven't been approved by supplier or seller.
• Do not allow your child to stand in the stroller.
• Never let stroller be used in step slope ,stairs, escalator, sand beach , rough roads, mud, etc.
• Always used the brakes when parking the stroller.
• Do not let the stroller nearby re.
• Do not add a mattress thicker than 25mm.
• The stroller is suitable for the child from O month to 36months.
• Child may slip into leg openings and strangle.
• Excessive weight may cause a hazardous unstable condition to exist.
1. PARTS:
1. Handle 2. Canopy; 3. Bumper bar; 4. Cushion; 5. Front wheel orientation; 6. Adjustable footrest; 7. Safety belt; 8. One hand fold;
THE ASSEMBLY OF STROLLER
Open the hook and pull the handle up until the stroller opened absolutely as showed in Figure 2,3.
THE ASSEMBLY OF FRONT WHEEL
Lift the front wheel (Figure 4). The opens of two front wheel bases are aligned to do the front foot, then hear the "click", which means that it has been in place. Press the detachable
button in bottom of the front wheel and the same time set aside the front wheels, you can detachable.
Ensure that all locks are in lock up position before pulling up and pushing the baby stroller.
THE ASSEMBLY AND DISASSEMBLY OF REAR WHEEL
The assembly of rear wheel: press down the button of the quick release device, push the rear wheel part in to hole until it be locked.
The disassembly of rear wheel: press down the button of the quick release device, pull out the wheel. Figure 5
Pull the xation right and left to and unlock the wheels. Figure 6
SAFETY BELT
Follow Figure 7: Press down the button to open the safety buckle.
Follow Figure 8: Insert the buckle to the socket, when hear click sound, then it locked.
Please always use the safety harness for safety. Put the crotch strap between baby`s legs and clasp the buckle.
BACKREST INSTRUCTION
Hold the button in picture with one hand, pull the belt to meet your required angl . Figure 9
Caution: adjust the backrest carefully when baby sit in.
LINKED BRAKE FOOTREST OF THE REAR WHEELS
Press the brake lever when stopping the stroller to avoid moving of the stroller. Push the stroller to check whether the locks are in lock up position. Figure 10
TWO STYLES CANOPY FOR WINTER AND SUMMER
Turn up two sides as arrowed direction on the Figure 11, fasten with button.
REMOVAL BUMPER BAR Figure 12
ADJUSTABLE FOOTREST Figure 13
FOLDING OF THE STROLLER
Follow the picture 14.1, fold the canopy rst.
Follow the picture 14. 2, Press down the second locked(picture shows),and hold the folding button to open the lock.
Follow the picture 14.3, press down the handle at the same time.
Follow the picture14.4, nally lock the hook on the side.
CLEANING AND CARE
Fabric parts:1. The fabrics must be cleaned with warm water and mild soap. After cleaning let get completely dry before you use it. If is absolutely forbidden to fold it and store it
before it is completely dry. 2. Do not use strong cleaning agents, bleach or agents with abrasive particles, in order to clean the product. It is forbidden to clean it in a washing machine,
dryer, dry cleaning, bleach and tumble-dry it.
Plastic and metal parts :1. The plastic and metal parts must be cleaned with a damp soft cloth and dried with dry soft cloth.
2. Do not let the product exposed to the harmful e ect of external factors - direct sunlight, rain, snow or wind. This may lead to damage of the metal and plastic parts. 3. When you
are not using the product, store it at a dry and well ventilated place, not in dusty, humid premises with very high or very low room temperatures.
ENGLISH