EdilKamin MYA Installation, Usage Et Maintenance page 35

ress and hold the "M" key on the remote control for 2 seconds. his turns on the clock regulation and by pressing the
key, the weekly timer function is accessed, with the display showing the description " RO RAMM ON OFF".
his function allows you to select the type of programming, which allows a ma imum of three ignitions to be set.
As you con rm the display with the key "M", one of the following options will appear:
NO RO . (no programme set)
DAILY RO RAM (single programme for every day of the week)
WEEKLY RO RAM. (speci c programme for each day individually)
Use the " " and " " keys to switch between programmes.
on rming by pressing the "M" key "DAILY RO RAM." and pressing the " " key, the choice of the number of programmes
(ignition e tinguishing) per day can be made.
Use the "DAILY RO RAM" to set identical programme s for every day of the week.
By then pressing the " " key, the following can be seen:
- rog. no.
- 1st prog. (one turn on and one turn off per day), 2nd prog. (identical), rd prog. (identical)
Use the " " key to show in reverse order.
If the 1st programme is selected, the turn on time is shown.
he display shows: 1 "ON" at 10 Use the " " and " " key to change the hour. on rm with the "M" key (All 1 On our 10).
he display shows: 1 "ON" at 0 Use the " " and " " key to change the minutes. on rm with the "M" key (1 Off min).
he same applies for the turn-off time to be set and for subsequent turning on and off.
on rm by pressing "M" and the wording "SA E " will appear on the display.y.
When con rming "WEEKLY RO RAM", you will need to choose the day to which the programming is to apply:
7 Sat; rogr.1; 1 Mon ; 2 ues; Wed; 4 hurs; 5 Fri; 6 Sa;
Once the day is set, use the keys " " and " " and con rm by pushing "M" key to choose 1 to ignitions, to programme in the
same way as for the "DAILY RO RAM", choosing whether or not to enable a programme for each day of the week, and if so
choosing number of interventions and at what times.
Should you make an error during programming, you can leave the programme without saving. As you press a key,
splay will show the word "no SA E".
(with self-regulation deactivated)
When the "M" key on the radio control is held down for two seconds and the display is scrolled using the " " and " " keys,
you come across the "User s Menu". When this is con rmed the display reads "AD - ELLE ; AD -DRAU
MENU" ( A ). he pellet drop can be adjusted manually by changing the capacity in percentage terms ( - 0 %).
By con rming this function with the menu key, you can access the function to adjust pellet loading. By decreasing the
value set, pellet loading is decreased. By increasing the value set, pellet loading increases. his function is useful if
changing the pellet type for which the stove has been calibrated and loading therefore needs correcting.
Should this correction not suf ce, contact the Edilkamin-authorised Dealer, to establish the new operating a is.
Flame status may vary depending on the type of pellet used, in addition to normal solid fuel ame variability and regular combu-
stion chamber cleaning carried out automatically by the boiler.
(N.B.: which does NO replace necessary cold suction by the user prior to ignition).
he stove is tted with an electronic function that detects the residual quantity of pellets in the tank.
he detection system is integrated into the electronic board, allowing you to see how many hours and kg are left until
pellet e haustion, at all times. For correct system function, it is important that the following procedure is followed during the rst
ignition (by the Dealer).
his provides a reference indicator.
does not accept any responsibility for differences from what is indicated (which may be due to e ternal factors).
INSTRUCTIONS FOR USE
reater precision is obtained by regularly zeroing the system before lling it again. Edilkamin
- 35
-
, he di-
and RADIO