GE PCHB920 Serie Manuel D'instructions

30" INDUCTION FREE-STANDING CONVECTION RANGE
WARNING
Electrical Shock Hazard
Death or serious injury can result from failure to follow these
instructions.
NOTE: Installation
WARNING
information for
reference only. See Tip-Over Hazard
A child or adult can tip the range and be killed.
Installation Instructions
Verify the anti-tip bracket has been properly installed
shipped with product
and engaged.
for complete details and Ensure the anti-tip bracket is re-engaged when the range
is moved.
before attempting to
Do not operate the range without the anti-tip bracket in
install. Anti-tip bracket
place and engaged.
must be attached to Failure to follow these instructions can result in death or
serious burns to children or adults.
the floor or wall to hold
either right or left rear leveling leg. Make sure leveling leg re-engages the bracket
when range is moved for any reason.
Adjacent Cabinet Attachment to Wall
Bracket
Or Final Location or Floor
Of Range Side Panel
Wall
Floor-Wood
Screw Must Enter
Wood or Metal
Bracket Side
Rear
Leveling Leg
Floor-Concrete
INDUCTION COIL SYSTEMS
The Induction Coils come in various sizes:
HOT SURFACE INDICATOR LEDS
SH. 1 of 4
31-17224
INDUCTION COIL CONTROLS
To use the cooktop induction coils:
NOTE: Appropriate cookware must be on
the induction coil for it to function.
Touch the ON/OFF pad for the desired
induction coil.
-
Touch the +
+/- pads to select the desired
Touch the ON/OFF
WARMING ZONE CONTROL
To use the warming zone:
ON/OFF pad.
- pad to select low.
+
+ pad or -
ON/OFF
POWER SHARING
display remains on H. Reduced power will not increase unless reset by the user.
Wall Plate
REMOVABLE OVEN DOOR
Slot
To Remove:
1.
2.
the unlocked position. This
may require a flat-blade
Arm
screwdriver.
3.
4. Close the door to the door-removal position.
5.
To Replace:
Arm
1.
of Slot
2.
3.
Indentation
4. Close the oven door.
Cooling Airflow:
bottom and flows upward between the inner and outer
door. DO NOT INSULATE THIS AIR CHANNEL.
To Service the Full-Glass Door:
1. Complete door assembly:
2.
NOTE:
be separated.
REMOVABLE OVEN DOOR (CONT.)
To Service the Full-Glass Door (cont.):
3. Liner assembly:
assembly.
door.
Door Gasket:
door panel.
To Service Gasket:
COOKTOP REMOVAL
To Remove:
1. Disconnect the power.
2.
cooktop to the chassis.
3.
4. Lift up the back end of the cooktop about
Cooktop
brackets.
5. Reverse the process to reinstall.
Screws
CAUTION:
Removal Position
CONTROL PANEL ASSEMBLY AND REMOVAL
To service:
1.
2.
3.
4.
CAUTION:
L1
BLACK
K908 K909
BROIL BAKE
K907
QTH
NOTES:
QUARTER TOP HEAT –
BAKE/TIME BAKE –
cycle for the balance of the bake operation with one element on at a time.
CLEAN –
broil units.
STEAM CLEAN
for the balance of the cycle.
ELECTRONIC OVEN CONTROL
CAUTION:
voltage is connected to oven. The Electronic Oven Control system consists of the
RC-15 control, Left and Right Wing Boards, oven sensor, door and lock assembly.
NOTE: Temperature/Mode Selection necessary for operation of Relay contacts.
VOLTAGE MUST BE PRESENT ACROSS TERMINALS L1 TO N FOR CONTROL TO OPERATE.
The controls for the oven system
Door Panel
Interface. The controls for the
cooktop module consist of two
induction filter board and both
one RTD oven sensor and a motor
door lock assembly with position
switches. There are four induction
OVEN SENSOR AND DOOR SWITCH OHMMETER TEST
Remove power from the oven. Make a resistance measurement from the side of the
leads at connector at rear of cavity
between broil element pins. If any
L2 N
RED WHITE
DLB
K915
K910
CONV
CONV
BAKE
BROIL
selected.
shows the time of day.
Components are electrically HOT on control when
CONTROLS SUMMARY
Induction Coils
Induction
Coils
CIRCUIT TERMINALS OHMS
Oven
Sensor
Unlatch
Latch
KEY PANEL TEST