Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Setting of user codes for signal output 1, 2 or 3:
Option number: [1] - [3] -> CodeID: [0] – [9] -> User code entry: [4 to 8 digits] -> Valida-
tion: [#]
Option number:
[1]: User code to activate signal output 1 of the receiver (group 1)
[2]: User code to activate signal output 2 of the receiver (group 2)
[3]: User code to activate signal output 3 of the receiver (group 3)
CodeID:
[0] – [9]: 10 user code IDs are available for each option number.
To delete a user code from the system, simply do not enter a user code in the
following step. The respective code with the code ID entered will then be
deleted.
User code entry:
Enter a user code with 4 to 8 digits at this step of the procedure.
Validation:
To validate, confirm your entry with the [#] button.
Changing the administrator code:
You can control the 3 signal outputs or lock signal output 1 with the administrator code.
Option number: [4] -> Master code: [4-8 digits long] -> Validation: [#]
If a new administrator code is entered, the old one is replaced.
To delete the administrator code, enter the following key combination: [4] [#]
Functions of the administrator code:
1) Enter the following to control the respective output with the administrator code:
[Administrator code] [#] [1] ---------------- Activates output 1 (code of group 1 is
[Administrator code] [#] [2] ---------------- Activates output 2 (code of group 2 is
[Administrator code] [#] [3] ---------------- Activates output 3 (code of group 3 is
2) Locking of user group 1 for signal output 1
To lock signal output 1 of group 1, enter the following key combination:
[Administrator code] [#] [9] -------------- All user codes of group 1 are activated/
To reactivate the signal output, enter the key combination above again.
Visitor codes (only for signal output 1):
The user codes can be entered here. Depending on the selection, they are valid for a
certain period from 0 to 99 hours.
Option number: [5] -> Visitor ID: [0 to 9 digits] -> Valid period: [0] [0] or [01 to 99] -> User
code: [4 - 8 digits] -> Validation: [#]
A maximum of 10 different user codes with different valid periods can be set.
To use a code once, enter [0] [0] as valid period.
For use over a certain period, enter the number of hours as valid period.
To delete a specific user code, enter the validation [#] immediately after en-
tering the user ID.
Response to several incorrect entries:
Option number: [6] -> Response to incorrect entry: [1] , [2] or [0] -> Validation: [#]
Response to several incorrect entries:
[1] - After entering the wrong code ten times, the number pad is locked for 30 seconds
[2] - After entering the wrong code ten times, the number pad is locked for 15 minutes
[0] - Number pad is not locked
Locking of the number pad can be cancelled with the administrator code.
Confirming the entered code manually or automatically:
Option number: [7] -> Confirmation mode: [1] or [2] -> Validation: [#]
Confirmation modes:
[1] - Automatic confirmation of the entered code (factory setting):
As soon as a correct combination of numbers was entered, signal output 1 is activated.
[2] - Automatic confirmation of the entered code:
Each code entered must be confirmed with the [#] button.
sent)
sent)
sent)
deactivated
Activating/deactivating the signal sounds:
Option number: [8] -> Signal sound modes: [1] , [2] or [0] -> Validation: [#]
Signal sound modes:
[1] - Signal sound partly switched on (factory setting):
All signal sounds except for the confirmation sound are switched on for entering the
building.
[2] - All signal sounds switched on:
High energy consumption, recommended for occasional use.
[3] - All signal sounds switched off:
Low energy consumption. Suitable for quiet surroundings.
Beeping during start-up of the device cannot be switched off.
Switching the background light on/off:
Option number: [9] -> Background light on/off: [0] or [1] -> Validation: [#]
Background light on: [1], Background light off: [0]
The background light always switches off automatically 10 seconds after
using the device.
The background light causes a high energy consumption.
Closing the programming mode:
[*] [*] ---- Resets the system to its normal operating mode
Declaration of conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare
that this product conforms to the fundamental requirements and other relevant regula-
tions of the 1999/5/EC directive.
The Declaration of conformity for this product is available at
www.conrad.com.
Disposal
Electrical and electronic products do not belong in your regular household
waste.
Please dispose of the product, when it is no longer of use, according to the
current statutory requirements.
Technical data
Operating voltage............................... 9 V alkaline battery
Operating current............................... 10 uA in sleep mode, 10 mA during sending
Operating temperature...................... -20 °C to +70 °C
Humidity ............................................... 5-95% relative humidity (non-condensing)
Working environment ........................ Outdoor and indoor areas, IP-55, approved for all
Number of user codes....................... 10 for each channel, total of 30 user codes for the
Number of visitor codes.................... 10 for signal output 1
Length of user code ........................... 4-8 digits, over one million combination possibili-
Duration of entry ................................ 10 seconds in total
Number pad ID code ......................... One of one million codes, pre-set
Operating frequency.......................... 433 MHz
Maximum sending distance ............. 50 m outdoors
Dimensions (H x W x T) ..................... 126.3 x 75.6 x 40 mm
Weight .................................................. 208 g net
Housing ................................................ ABS
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2016 by Conrad Electronic SE.
weathers
3 signal outputs
ties for an 8-digit code
Publicité
Table des Matières
