Safety Instructions; Description And Specifications; Installation - General; Close Coupled Units - Xylem GOULDS ICS Manuel D'utilisation

SAFETY INSTRUCTIONS

TO AVOID SERIOUS OR FATAL PERSONAL INJURY
OR MAJOR PROPERTY DAMAGE, READ AND
FOLLOW ALL SAFETY INSTRUCTIONS IN THE
MANUAL AND ON THE PUMP.
This is a SAFETY ALERT SYMBOL. When
you see this symbol on the pump or in the
manual, look for one of the following signal
words and be alert to the potential for
personal injury or property damage.
Warns of hazards that WILL cause serious
DANGER
personal injury, death or major property
damage.
Warns of hazards that CAN cause serious
WARNING
personal injury, death or major property
damage.
Warns of hazards that CAN cause personal
CAUTION
injury or property damage.
NOTICE: INDICATES SPECIAL INSTRUCTIONS
WHICH ARE VERY IMPORTANT AND
MUST BE FOLLOWED.
THIS MANUAL IS INTENDED TO ASSIST IN THE
INSTALLATION AND OPERATION OF THIS UNIT.
THOROUGHLY REVIEW ALL INSTRUCTIONS AND
WARNINGS PRIOR TO PERFORMING ANY WORK
ON THIS PUMP.
MAINTAIN ALL SAFETY DECALS.
Install, ground and wire accord-
WARNING
ing to local and National Electrical
Code Requirements.
Install an all leg disconnect switch
near the pump.
Disconnect and lockout electrical
power before installing or servicing
Hazardous voltage
can shock, burn or
the pump.
cause death.
Electrical supply must match motor's
nameplate specifications. Incorrect
voltage can cause fire, damage motor
and void the warranty.
Single phase pump motors are equipped with an
automatic thermal protector, which opens the motor's
electrical circuit when an overload condition exists.
This can cause the pump to start unexpectedly.
DESCRIPTION and SPECIFICATIONS
The Models ICS, close coupled, and ICS-F, frame mounted,
are single stage, end suction pumps designed for ultra pure
water systems, beverage processing, chemical service and
selected OEM applications.
The pumps are of back pullout configuration, with NPT
suction and discharge connections and have investment cast
AISI Type 316 stainless steel casings, open impellers and
seal housing. All pumps are equipped with O-ring shaft
sleeve protection and are available with a variety of optional
mechanical seals.
Close coupled units are equipped with C-face NEMA motors
with threaded shaft extensions. Frame mounted units can be
baseplate mounted and are available with spacer couplings or
may be belt driven.
Close coupled units are available with single and three phase
ODP , TEFC and explosion proof motors. Consult with your
distributor/dealer for additional information.
NOTICE: INSPECT UNIT FOR DAMAGE AND
REPORT ALL DAMAGE TO CARRIER
IMMEDIATELY.
MAXIMUM OPERATING LIMITS
Liquid Temperature:
212 F (100 C) – standard mechanical seal
250 F (120 C) – OPTIONAL mechanical seal
Operating Pressure: 175 PSI (1203 kPa)
Starts per Hour: 20, evenly distributed
INSTALLATION – GENERAL
• Locate the pump as near to the liquid source as possible.
• If pump repriming capability is required, the pump suction
MUST be below the source of the liquid level.
• Protect the pump and piping from freezing temperatures.
• Allow adequate space around the unit for service and
ventilation.
CLOSE-COUPLED UNITS
• Units may be installed horizontally, inclined or vertically.
DO NOT MOUNT MOTOR BELOW
WARNING
PUMP. FLUID LEAKAGE ONTO
Hazardous
MOTOR CAN CAUSE A SHOCK,
voltage
BURN OR DEATH.
• Unit foundation must be flat and substantial to avoid pipe
strains when bolts are tightened. Use rubber mounts under
motor to minimize noise and vibration.
• Tighten motor holddown bolts BEFORE connecting the
suction and discharge piping.
FRAME-MOUNTED UNITS
• Place the baseplate upon the foundation and disconnect the
coupling halves. DO NOT reconnect the coupling until the
alignment procedures have been completed.
• It is recommended that the baseplate be grouted to a
foundation with a solid footing, per Figure 1.
3