Learn Feature - Ruwido M-4 Manuel D'utilisation

Automatic search feature
Alternatively, or if either in case of manual programming or with automatic programming, the correct code for your
equipment cannot be found, you may use the automatic search feature.
1) Switch on your TV, satellite receiver or your DVB-T / cable box (STB), your DVD / Bluray player or recorder
(DVD) and your audio equipment.
2) Press and hold the TV (
programme until the signal LED (
3) Using the numeric buttons, enter
the code 1 0 0 1 for TV,
the code 3 0 0 1 for STB or
the code 5 0 0 1 for DVD.
The signal LED ( ) fl ashes twice in order to confi rm that the search mode has been activated.
4) For TV and STB, hold the standby button ( ) or, for DVD, the stop button ( ) of your m_4 pressed until the
equipment switches off or, in the case of the DVD, playback stops. This step may take several minutes.
5) As soon as the equipment responds, press the OK button (
the signal LED ( ) fl ashes twice.
6) Test the functionality of your remote control using the standby button ( ) and then with the buttons 1 to 47
(according to the function description table).
7) If the equipment responds properly to all functions, your m_4 is correctly programmed and can be used.
Note :
It could happen, that during the search process, the m_4 fi nds several codes to which your TV set responds, but
where all buttons do not function for each code. In this case, the search process should be re-started (steps 2 to
7) until you obtain the best code. Re-starting the search process starts at the last saved programming.
Code reader
The code reader can be used to display the codes that you have found in the search process so that you can
make a note of them:
1) Press and hold the TV (
programme until the signal LED (
2) Use the number buttons to enter the code 0 0 0 2. The Signal LED (
3) Push 1 and count the number of times the Signal LED fl ashes; this is the fi rst number.
4) Push 2 and count the number of times the Signal LED fl ashes; this is the second number.
5) Push 3 and count the number of times the Signal LED fl ashes; this is the third number.
6) Push 4 and count the number of times the Signal LED fl ashes; this is the fourth number.
Note :
The Signal LED does not fl ash if the number is 0. The steps 3 to 6 can be carried out in any order and as many
times as may be required.

Learn feature

Alternatively, or if either in case of manual programming or with automatic programming, the correct code for your
equipment cannot be found, you may use the learn feature.
The learn feature may also be used if certain button functions of the original remote control are not included in the
database.
Positioning the m_4 and original remote control (Range test)
In order to ensure that the remote control can receive the signal, both remote controls should be placed opposite
one another with their transmission diodes facing each other. The distance between both remote controls should
not be greater than 5 cm.
You may use the range test to determine the optimal position for learning the codes:
1) Press and hold the TV (
programme until the signal LED (
2) Enter the code 0 0 1 1 using the numeric buttons. The signal LED fl ashes twice again.
3) Now, the signal LED lights up in orange and displays the quality of the signals received.
Now place the original remote control and press and hold any button on it.
Change the distance to the m_4 remote control until the signal LED lights up in green.
BA m_4 Universal, 135x215 mm CS6.indd 12 BA m_4 Universal, 135x215 mm CS6.indd 12
), STB ( ), DVD ( ) or AUX (
tv stb dvd
) fl ashes twice.
), STB ( ), DVD ( ) or AUX (
tv stb dvd
) fl ashes twice.
), STB ( ), DVD ( ) or AUX (
tv stb dvd
) fl ashes twice.
) button depending on the level that you wish to
aux
) to confi rm the programming and hold it until
ok
) button depending on the level that you wish to
aux
) fl ashes twice again.
) button depending on the level that you wish to
aux
12
11.09.2012 16:03:12 11.09.2012 16:03:12