Manual Programming - Ruwido M-4 Manuel D'utilisation

Manual Programming

1) Switch on your TV, satellite receiver or your DVB-T / cable box (STB) and your DVD / Bluray player or recorder
(DVD).
2) Page to the brand of your appliance under „TV", „STB" or „DVD" in the list of codes. One or more 4-digit codes
are displayed for each brand.
Note :
On our website www.ruwido-consumer.com you can use the code search function in the support area to enter
your set model number directly in order to obtain the appropriate code. This will save you having to test
several codes.
3) Press and hold the (
tv
until the signal LED (
4) Use the number keys to enter the fi rst four-digit code from the code list for the brand that you have selected.
The signal LED ( ) fl ashes twice to indicate that the code has been accepted.
5) Test the functionality of your remote control using the standby button ( ) and then with the buttons 1 to 47
(according to the function description table).
6) If the equipment does not respond or only partially to the button commands, repeat the steps 3 to 5 using the
next code from the list of codes.
7) If the equipment responds properly to all functions, your m_4 is programmed correctly and can be used.
Please make a note of the code used for reference.
My programming codes to use:
TV STB
Automatic programming according to the brand
Alternatively, or if in case of manual programming the correct code for your equipment cannot be found, you may
use the automatic search for brand for programming.
1) Switch on your TV, satellite receiver or your DVB-T / cable box (STB) and your DVD / Bluray player or recorder
(DVD).
2) Page to the brand of your equipment under the relevant „TV", „STB" or „DVD" section in the list of brands
given in the Appendix of this manual. There is a 3-digit brand code for each brand.
3) Press and hold the TV (
programme until the signal LED (
4) Using the numeric buttons, enter
the code 1 0 0 3 for TV,
the code 3 0 0 3 for STB or
the code 5 0 0 3 for DVD.
The signal LED ( ) fl ashes twice in order to confi rm that the search mode has been activated.
5) Use the number keys to enter the three-digit brand code from the brand list for the brand that you have
selected. The signal LED (
6) For TV and STB, hold the standby button ( ) or, for DVD, the stop button ( ) of your m_4 pressed until the
equipment switches off or, in the case of the DVD, playback stops. This step may take several minutes.
7) As soon as the equipment responds, press the OK button (
the signal LED ( ) fl ashes twice.
8) Test the functionality of your remote control using the standby button ( ) and then with the buttons 1 to 47
(according to the function description table).
9) If the equipment responds properly to all functions, your m_4 is correctly programmed and can be used.
Note :
It could happen, that during the search process, the m_4 fi nds several codes to which your TV set responds, but
where all buttons do not function for each code. In this case, the search process should be re-started (steps 3 to
9) until you obtain the best code. Re-starting the search process starts at the last saved programming.
BA m_4 Universal, 135x215 mm CS6.indd 11 BA m_4 Universal, 135x215 mm CS6.indd 11
), ( ), ( ) or ( ) button depending on the level that you would like to programme,
stb dvd aux
) fl ashes twice.
DVD AUX
), STB ( ), DVD ( ) or AUX (
tv stb dvd
) fl ashes twice.
) fl ashes twice to indicate that the code has been accepted.
) button depending on the level that you wish to
aux
) to confi rm the programming and hold it until
ok
11
11.09.2012 16:03:09 11.09.2012 16:03:09