Cleaning, Maintenance And Ordering Of Spare Parts; Disposal And Recycling - EINHELL TE-CS 18/190 Li BL-Solo Instructions D'origine

Warning!
Do not use grinding wheels!
The diameters of the saw blades used must cor-
respond to the diameters specifi ed on the hand-
held circular saw blade!
Use only recommended saw blades!
Use the saw blade key (13) supplied to change
the saw blade. The saw blade key (13) is stored
in the housing. If required, pull the saw blade key
(13) out of the housing (see Figure 13).
Important. The hand-held circular saw must not
be operated with the saw blade key (13) inserted
in it.
•
Press the spindle lock (11).
•
Undo the screw to secure the saw blade (17)
using the saw blade key (13).
•
Push back and secure the moving swing
guard hood (20) using the lever for the swing
guard hood (21).
•
Remove the flange (18) and the saw blade
(12) in a downwards direction.
•
Clean the flange and insert the new saw bla-
de. Pay attention to the running direction (see
arrow on the guard hood and saw blade).
•
Remove the clamping flange (18) and the
saw blade (12) in a downwards direction.
•
The circular saw is equipped with a change
flange (19) which can be turned to allow both
saw blades with a 20 mm mounting hole and
saw blades with a 30 mm mounting hole to
be fitted.
•
To mount a 20 mm saw blade, fit the change
flange (19) as shown in figure 17.
•
To mount a 30 mm saw blade, fit the change
flange (19) as shown in figure 18.
•
Clean the clamping flange (18) and then fit
clamping flange (18) and new saw blade. Pay
attention to the running direction (see arrow
on the guard hood and saw blade).
•
Tighten the screw to secure the saw blade
(17), check it runs true.
•
Before you press the On/Off switch, make
sure that the saw blade is correctly fitted and
that moving parts run smoothly and the clam-
ping screws are tightened securely.
6.5 LED lamp (Fig. 1/Item 5)
The LED lamp (5) can be used in poor lighting
conditions to additionally illuminate the cutting
position. The LED lamp (5) will come on automa-
tically as soon as you press the locking button for
the On/Off switch (3).
GB
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the battery pack before starting
any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info

8. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
- 25 -