Usb Operation - Aiwa MSBTU-300 Mode D'emploi

14
en
AUXILIARY INPUT OPERATION
THE UNIT CAN BE USED TO PLAY THE MUSIC
FROM MANY TYPES OF EXTERNAL DEVICE
1. Connect by using a 3.5mm
the external
Male-to-Male Stereo cable
device to the AUX connector/ jack of the
unit.
Press repeatedly to select the
2. SOURCE
LINE IN mode.
3. Start playback on the external audio
device. Adjust the volume on the audio
device (do not set the volume to a
high level in order to avoid distortion).
You may also adjust the volume on the
appliance. To control playback function,
use the controls on the external audio
device.

USB OPERATION

YOU CAN ENJOY MEDIA FILES SAVED ON
AN USB DEVICE BY CONNECTING THE USB
DEVICE TO THE USB PORT OF THE UNIT
1. Connect the USB device to the USB
port of the unit.
2. Select the USB mode by pressing CD/USB
on your remote control.
In the unit, press button and
SOURCE
select the CD MODE . Then wait until the
unit search for a playable CD. If there isn't
a CD inside the unit it will jump directly to
the USB mode.
Select a file you want to play using
3.
/ / / or instead you may select
directly the file with the numerical keys.
Press on the remote control or on the
4.
unit to start the playback.
5. Turn the VOLUME knob or press
to increase or decrease
VOL+/ VOL-
volume level.
6. Press button on the unit or on the
remote control to playback.
STOP USB
Before disconnecting the device,
7. USB
change the source by pressing SOURCE
button.
COMPATIBLE USB DEVICE
MP3 PLAYER:
Flash type MP3 player.
USB FLASH DRIVE:
Devices that support USB 2.0 or USB 1.1.
The USB function may not be available
depending on device.
Device which require additional program
installation when you have connected it to
a computer, are not supported.
IMPORTANT:
- Switching from CD to USB from the unit
can take a few seconds.
- Do not extract the USB device while in
operation.
- For a large USB capacity, it may take longer
than a few minute to be searched.
- To prevent data loss, back up all data.
- If you use a USB extension cable or USB
hub, the USB device is not recognized.
- Using NTFS file system is not supported
(Only FAT (16/32) file system is supported).
- This unit is not supported when the total
number of files is 1000 or more.
- External HDD, locked devices or hard type
USB devices are not supported.
PROGRAM MODE
The operation of are
PROGRAM MODE
as the same as that of CD / MP3 .
Please refer to BASIC OPERATION
section paragraph
CD/MP3 PROGRAM:
CREATING YOUR OWN PLAYLIST .
BLUETOOTH OPERATION
ººº
IMPORTANT:
Prior to use Bluetooth function, your micro system should be paired firstly with your Bluetooth device.
("Pairing" means establish connection between Bluetooth devices such as MOBILE PHONE, TABLETS,
PC, ETC).
1. Press the SOURCE button to switch into
the .
BLUETOOTH MODE
(fig. 1)
In Bluetooth mode, Red and Blue LED
2.
indicators will flash alternatively and a
voice prompt will announce Bluetooth
pairing mode.
Then the micro system will search automatically
for Bluetooth devices.
3. Turn on Bluetooth functionality on your
device and make it discoverable (see your
devices instructions to add or setup a
Bluetooth device).
4. Search for Bluetooth equipment MSBTU-300
is your micro system identification.
(fig. 2)
Red status indicator switches to blue
light which means that devices are
successfully paired. (During the paring,
if the Bluetooth Version is below 3.0, you
need to input code"0000").
Your Bluetooth device stores the micro
system unique identification at the same
time.
Notes:
• The effective range of Bluetooth devices is 10 meters. Once paired, your device should connect
to the .
MSBTU-300
15
(fig. 1)
(fig. 2)