Residual Risks - Senix GTC4QL-L Manuel De L'opérateur

may be malfunctioning.
35. In start-up or during operation of the engine, never
touch hot parts such as the muffler, the high voltage
wire, or the spark plug.
36. After the engine has stopped, the muffler is still hot.
Never place the unit in any places where there are
flammable materials (dry grass, etc.), combustible
gasses, or combustible liquids.
37. Pay special attention to operation in the rain or just
after the rain as the ground may be slippery.
38. If you slip or fall to the ground, release the throttle
lever immediately.
39. Be careful not to drop the unit or hit it against
obstacles.
40. Before proceeding to adjust or repair the unit, be
sure to stop the engine and detach the spark plug.
41. When the machine is placed in storage for a
long time, drain fuel/oil from the fuel/oil tank and
carburetor, clean the parts, and move the machine
to a safe place.
42. Make periodic inspections to ensure safe and
efficient operation. For a thorough inspection of
your unit, contact customer support.
43. Keep the unit away from fire or sparks.
44. Keep your body warm, especially the head, neck,
feet, ankles, hands, and wrists.
45. Maintain good blood circulation by performing
vigorous arm exercises during frequent work breaks
and also by not smoking.
46. Limit the hours of operation.
47. If you experience discomfort, redness and swelling
of the fingers followed by whitening and loss of
feeling, consult your physician before further
exposing yourself to cold and vibration.
48. Always wear ear protection. Loud noises for long
periods can cause hearing loss, even permanent
deafness.
49. Wear no-slip heavy duty work gloves to improve
your grip on the handle. Gloves also reduce the
transmission of machine vibration to your hands.
WARNING:
The string head is still dangerous while the machine is
coasting to a stop.
50. Do not lay the machine on the side; otherwise the
fuel could.
51. Fuel evaporation during refueling and exhaust
gases are harmful to the operator and people
around the unit.
52. Make sure that the fuel evaporation and exhaust
gases will not drift to the face of operator and keep
other people away from your working area.
53. Do not allow children or untrained individuals to use
this unit.

RESIDUAL RISKS

WARNING:
Even when the unit is used as prescribed it is not
possible to eliminate all residual risk factors. The
following hazards may arise in connection with the unit's
construction and design:
4
• Damage to lungs if an effective dust mask is not worn.
• Damage to hearing if effective hearing protection is
not worn.
• Health defects resulting from vibration emission if the
unit is being used over long periods of time or not
adequately managed and properly maintained.
WARNING:
This unit produces an electromagnetic field during
operation. This field may, under some circumstances,
interfere with active or passive medical implants. To
reduce the risk of serious or fatal injury, we recommend
persons with medical implants to consult their physician
and the medical implant manufacturer before operating
this unit.
WARNING:
Inspect unit before each use. Replace damaged parts.
Check for fuel leaks. Make sure all fasteners are in
place and secure. Replace cutting attachment parts that
are cracked, chipped, or damaged in any way. Make
sure the cutting attachment is properly installed and
securely fastened. Be sure the cutting attachment shield
is properly attached and in the position recommended
by the manufacturer. Use only flexible, nonmetallic line
recommended by the manufacturer. Never use, for
example, wire or wire-rope, which can break off and
become a dangerous projectile.
WARNING:
Do not operate the unit inside a closed environment,
such as a room or building; breathing carbon monoxide
from exhaust fumes can kill.
WARNING:
Mix and pour fuel outdoors where there are no sparks
and flames. Slowly remove the fuel cap only after
stopping the engine. Do not smoke while fueling or
mixing fuel. Wipe spilled fuel from the unit. Move at
least 3 m (10 ft) away from the fueling source and site
before starting engine.
WWW.SENIXTOOLS.COM