Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
To remove an accessory, grasp the
accessory and firmly pull it off.
Usage
WARNING
:
system will withstand the level of torque
generated by the tool. Excessive torque
may cause breakage and possible
personal injury.
1. Place the accessory on the fastener
head. Keep the tool pointed straight at
the fastener.
2. Squeeze the trigger switch (1) to start
operation. Always check torque with a
torque wrench, as the fastening torque
is affected by many factors including the
following:
• Accessory size: Failure to use the
correct accessory size will cause a
reduction in fastening torque.
• Bolt Size: Larger bolt diameters
generally require higher fastening
torque. Fastening torque will also vary
according to length, grade, and torque
coefficient.
• Bolt: Ensure that all threads are free of
rust and other debris to allow proper
fastening torque
• Material: The type of material and
surface finish of the material will affect
fastening torque.
• Fastening Time: Longer fastening
time results in increased fastening
torque. Using a longer fastening time
than recommended could cause the
fasteners to be overstressed, stripped or
damaged.
Capacity
Your 1/2" (12.7 mm) impact wrench uses
sockets with 1/2" (12.7 mm) square drive
ends.
LED Work Light
When drill is activated by squeezing the
trigger switch (1), the integrated LED work
light (6) will automatically illuminate the
work area and will automatically turn off
after the trigger switch is released. If the
trigger switch remains depressed, the work
light will remain on.
NOTE: The work light is for lighting
the immediate work surface and is not
intended to be used as a flashlight.
Cleaning
WARNING
:
To reduce the risk of
serious personal injury, turn tool off and
remove the battery pack before making
nsure fastener and/or
E
any adjustments or removing/installing
attachments or accessories. An accidental
start-up can cause injury.
WARNING
of all air vents with clearn, dry air at least
once a week. To minimze the risk of eye
injury, always wear ANSI Z87.1 approved
eye protection when performing this.
WARNING
other harsh chemicals for clearning the
non-metallic parts of the tool. These
chemicals may weaken the plastic
materials used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
Charger Cleaning
Instructions
WARNING
Disconnect the charger from the AC outlet
before cleaning.
Dirt and grease may be removed from the
exterior of the charger using a cloth or soft
non-metallic brush. Do not use water or
any cleaning solutions.
Replacement Parts
Use only identical replacement parts. For a
parts list or to order parts, visit our service
website at www.portercable.com. You
can also order parts from your nearest
PORTER-CABLE Factory Service Center or
PORTER-CABLE Authorized Warranty Service
Center. Or, you can call our Customer Care
Center at (888) 848-5175.
®
The RBRC
The RBRC® (Rechargeable
Battery Recycling Corp oration)
Seal on the nickel cadmium,
nickel metal hydride or lithium-
ion batteries (or battery packs)
indicates that the costs to recycle these
batteries (or battery packs) at the end of
their useful life have already been paid
by BLACK+DECKER. In some areas, it
is illegal to place spent nickel cadmium,
nickel metal hydride or lithium-ion
batteries in the trash or municipal solid
waste stream and the Call 2 Recycle®
program provides an environmentally
conscious alternative.
Call 2 Recycle, Inc., in cooperation with
BLACK+DECKER and other battery
users, has established the program in the
United States and Canada to facilitate
the collection of spent nickel cadmium,
nickel metal hydride or lithium-ion
batteries. Help protect our environment
9
:
Blow dirt and dust out
:
Never use solvents or
:
Shock hazard.
Seal
Publicité
Table des Matières
