Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
e ) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool's operation. If damaged, have the power
tool repaired before use. Many accidents are
caused by poorly maintained power tools.
f ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g ) Use the power tool, accessories and tool bits, etc.
in accordance with these instructions, taking
into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could result
in a hazardous situation.
5) Service
a ) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Safety Instructions for Planers
•
To reduce the risk of injury, user must read and understand
instruction manual before operating planer.
•
Wait for the cutter to stop before setting the tool down. An
exposed rotating cutter may engage the surface leading to
possible loss of control and serious injury.
•
Hold power tool by insulated gripping surfaces only,
because the cutter may contact its own cord. Cutting a
"live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
•
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against the body leaves it unstable and
may lead to loss of control.
Planer Safety Rules
•
Be sure the voltage agrees with specific data on the
nameplate.
•
Make certain that the switch is in the off position before
connecting plug to a power source.
•
Be sure to switch OFF immediately if tool is jammed in
work.
•
Be sure tool is set for correct depth before turning switch
to ON.
•
Be sure to use specified replacement parts only.
•
Be sure tool is disconnected from power source when
cleaning or making adjustments to the tool.
•
Be sure to maintain tool with care. Follow instructions for
lubricating and changing accessories.
•
Stay alert – never operate the unit when tired or under the
influence of drugs, alcohol, or medication.
•
Be sure to store tool in a clean dry place after
disconnecting from power source.
•
Do not use in dangerous environments. Do not use near
flammable substances, in damp or wet locations, or
expose to rain.
•
Be sure that the blades are mounted as described in the
instruction manual and check that all screws are firmly
tightened before connecting unit to power source.
•
Keep air vents unobstructed for proper motor cooling.
•
DO NOT lay tool down on shoe when the blades are
exposed. This can chip the blades.
•
Keep side discharge chute unobstructed at all times.
•
Never reach under the tool for any reason unless it is
turned off and UNPLUGGED. BLADES ARE EXPOSED AND
EX TREMELY SHARP.
•
Use this tool for working with wood and wood products
only.
•
Never operate without securely holding the front handle.
•
Always operate planer with two hands.
•
Planer blades are extremely sharp. Handle with great care.
•
Clean out your tool often, especially after heavy use.
Additional Safety Information
WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or
dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
•
ANSI Z87.1 eye protection (CAN/CSA Z94.3),
•
ANSI S12.6 (S3.19) hearing protection,
•
NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to the State
of California to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
•
lead from lead-based paints,
•
crystalline silica from bricks and cement and other
masonry products, and
•
arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
•
Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing
dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/
or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use
NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles
away from face and body.
English
3
Publicité
Table des Matières
