Special Functions; Other Functions - Brandt TI1000B Mode D'emploi

SPECIAL COOKING ZONES
MAXIZONE cooking zone
2.7
Press the button to directly access the complete
zone. An animation shows when the zone is swit-
ched on. You can now adjust the power by pressing
the + or - buttons.

SPECIAL FUNCTIONS

Direct Access function (depending on model):
This function allows you to modify the power levels
defined in the presets (except for the BOOST). Your
cooking zone must be turned off. Select the preset
or to modify, by keeping your finger on it. Set the
new power setting by pressing the + or - button. A
beep will confirm your action after a few moments.
Note: The power levels set must be between 1 and
7 for the first button and 8 and 12 for the second
button.

OTHER FUNCTIONS

CLEAN LOCK function: This function allows you
to temporarily lock your hob while cleaning. To acti-
vate Clean Lock: Your cooking hob must be turned
on or off. Briefly press the
heard and the indicator blinks. After a predefined
time, the lock will automatically disengage. A beep
sounds and the indicator goes out. You can stop the
Clean Lock function by a long press on the
ton.
3
For light cleaning, use a disinfectant sponge. Thoroughly
moisten the zone to be cleaned with hot water, then wipe
off.
When cooked dirt, sugar laden spills, melted plastic
have accumulated, use a disinfectant sponge and/or a
special scraper for glass to remove them. Thoroughly
moisten the zone to be cleaned with hot water. Use a
scraper for glass to remove the large bits, follow with the
rough side of a disinfectant sponge, and then wipe off.
For scale stains and marks, apply hot white vinegar to
the affected area, leave it to act and wipe off using a
soft cloth.
For shiny metal colouring marks and weekly cleaning,
use a special cleaner for ceramic glass. Apply the spe-
cial product (which shall preferably comprise silicon
with a protective effect) onto the ceramic glass.
Important note: Never use abrasive powders or
sponges. Prefer special creams and sponges for deli-
cate dishes.
button, a beep is
but-
4
On start up:
You will see a light up display. This is normal. It will
disappear after 30 seconds.
Your installation trips the circuit breaker or only one
side works. The electrical hook-up of your hob is
incorrect.
Check its compliance (refer to the Connection sec-
tion).
The hob produces an odour during the first cooking ses-
sions. The appliance is brand new. Heat up each zone
for a half hour with a pan full of water.
On start up:
The hob is not working and the indicator lights on
the control panel are not on.
The appliance is not receiving electricity. The electri-
cal supply is defective or the hook-up is incorrect.
Inspect the electrical circuit breaker and fuses.
The hob is not working and another message is dis-
played. The electronic board is functioning incorrectly.
Call the After Sales Service Department.
The hob does not work, and
played. Unlock the child safety device (2.6).
During operation:
The hob does not work, and
and an audible signal is heard.
There was an overflow or an object is in contact
with the control panel. Clean the hob or remove the
object and restart cooking (4.1.1 - 4.1.2).
A series of or F7 are displayed.
The electronic circuits have overheated (refer to the
Fitting heading).
While a zone is heating, the control panel indicators
continue to blink.
The cookware used is unsuitable (refer to the Cook-
ware heading).
The cookware makes noise and your hob makes a
clicking noise during cooking.
This is normal. With some kinds of cookware, this is
heard as energy passes from the hob to the cook-
ware.
The fan continues to function a few minutes after your
hob is turned off.
This is normal. This allows the electronics to cool.
The cookware makes noise and your hob makes a
clicking noise during cooking.
This is normal. With some kinds of cookware, this is
heard as energy passes from the hob to the cookware.
The fan continues to function a few minutes after
your hob is turned off.
This is normal. This allows the electronics to cool.
E n g l i s h
or are dis-
or F7 is displayed