Additional Safety Rules - Skil 3320-01 Consignes D'utilisation/De Sécurité

Tool Use
DON'T FORCE TOOL
It will do the job better and safer at the rate for which
it was designed.
USE THE RIGHT TOOL
Don't force a small tool or attachment to do the job of
a heavy duty tool. Don't used tool for purpose not
intended—for example, don't use a circular saw for
cutting tree limbs or logs.
SECURE WORK
Use clamps or a vise to hold work. It's safer than
using your hand and it frees both hands to operate
the tool.
NEVER LEAVE TOOL RUNNING UNATTENDED
Turn power off. Don't leave tool until it comes to a
complete stop.
Tool Care
DO NOT ALTER OR MISUSE TOOL
These tools are precision built. Any alteration or
modification not specified is misuse and may result in
dangerous conditions.
AVOID GASEOUS AREAS
Do not operate electric tools in a gaseous or
explosive atmosphere. Motors in these tools normally
spark, and may result in a dangerous condition.
MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and
changing accessories. Inspect tool cords periodically
and if damaged, have repaired by authorized service
facility. Inspect extension cords periodically and
replace if damaged. Keep handles dry, clean and
free from oil and grease.
Before connecting the tool to a power
!
source (receptacle, outlet, etc.), be sure
voltage supplied is the same as that specified on the
WARNING
nameplate of the tool. A power source with a voltage
greater than that specified for the tool can result in
serious injury to the user, as well as damage to the
tool. If in doubt, DO NOT PLUG IN THE TOOL. Using
a power source with a voltage less than the nameplate
rating is harmful to the motor.

Additional Safety Rules

3.
For your own safety, do not operate your
!
drill press until it is completely assembled
and installed according to the instructions ... and until
WARNING
you have read and understood the following:
1. Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5
2. Motor Specifications . . . . . . . . . . . . . . . . . . . . . . 6
3. Getting To Know Your Drill Press . . . . . . . . . . . 9
4. Assembly and Adjustments . . . . . . . . . . . 10–17
5. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 17–19
7. Maintaining Your Drill Press . . . . . . . . . . . . . . 20
8. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .20
9. STABILITY OF THE DRILL PRESS
If there is any tendency of the drill press to tilt or move
during any use, bolt it to the bench top or to a piece of
3/4" exterior plywood large enough to stabilize the drill
press. Bolt the plywood to the underside of the base so
it extends beyond the sides of the base. DO NOT USE
PRESSED WOODS PANELS. They can break
unexpectedly. If the workpiece is too large to easily
support with one hand, provide an auxiliary support.
10. LOCATION
Use the drill press in a well lit area and on a level
surface, clean and smooth enough to reduce the risk of
trips and falls. Use it where neither the operator nor the
casual observer is forced to stand in line with a potential
kickback.
11. PROTECTION: Eyes, hands, ears and body.
TO AVOID BEING PULLED INTO
!
THE SPINNING TOOL—
WARNING
DO NOT WEAR: Loose fitting gloves
Necktie
Loose clothing
Jewelry
DO: TIE BACK LONG HAIR
ROLL LONG SLEEVES ABOVE ELBOWS
a. If any part of your drill press is missing, malfunc-
tioning, has been damaged or broken ... such as the
motor switch, or other operating control, a safety device
or the power cord ... cease operating immediately until
the particular part is properly repaired or replaced.
b. Never place your fingers in a position where they
could contact the drill bit or other cutting tool if the
workpiece should unexpectedly shift or your hand
should slip.