Black & Decker KD1010 K Mode D'emploi page 6

ENGLISH
Labels on tool
The following pictograms are shown on the tool along with the
:
date code:
Warning! To reduce the risk of injury, the user
f
must read the instruction manual.
Wear ear protectors with Impact drills. Exposure
to noise can cause hearing loss
Electrical safety
#
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
1. On/Off switch
2. Speed selector dial
3. Drilling mode selector
4. Operating mode selector
5. Tool holder
6. Side handle
7. Depth stop
8. Grease cap
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle (fig. A)
Turn the grip counterclockwise until you can slide the side
u
handle (6) onto the front of the tool.
Rotate the side handle into the desired position.
u
Tighten the side handle by turning the grip clockwise.
u
Fitting and setting the depth stop (fig. A)
Slacken the knob (9).
u
Insert the depth stop (7) into the mounting hole as shown.
u
Set the depth stop (7) to the desired position. The maxi-
u
mum drilling depth is equal to the distance between the tip
of the drill bit and the front end of the depth stop.
Tighten the knob (9).
u
Fitting an accessory (fig. B - D)
Clean and grease the shank (10) of the accessory.
u
Pull back the sleeve (11) and insert the shank into the tool
u
holder (5).
Push the accessory down and turn it slightly until it fits into
u
the slots.
Pull on the accessory to check if it is properly locked.
u
6
(Original instructions)
The hammering function requires the accessory to be able
to move axially several centimetres when locked in the
tool holder.
To remove the accessory, pull back the sleeve (11) and
u
pull out the accessory.
Keyed chuck (fig. D)
Open the chuck by turning the sleeve (12) anti-clockwise.
u
Insert the bit shaft (13) into the chuck.
u
Insert the chuck key (14) into each hole (15) in the side of
u
the chuck and turn clockwise until tight.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Warning! Do not apply chisels when the tool is in the drilling
mode.
Selecting the operating mode (fig. F)
The tool can be used in three operating modes.
To operate the drilling mode selector (3), rotate it towards
u
the required position, as indicated by the symbols.
To operate the operating mode selector (4), push the
u
unlock button (16) and rotate the selector towards the
required position, as indicated by the symbols.
Drilling
For drilling in steel, wood and plastics, and for
s
u
screwdriving set the operating mode selector (4) to the
position and the drilling mode selector (3) to the
position.
Hammer drilling
For hammer drilling in masonry and concrete, set the
s
u
operating mode selector (4) to the drilling mode selector
s
(3) to the position and the drilling mode selector (3)
to the position. When hammering, the tool should
not bounce and run smoothly. If necessary, increase the
speed.
Hammering
For hammering with spindle lock, and for light chiselling
q
u
and chipping, set the operating mode selector (4) to the
position and the drilling mode selector (3) to the
position.
When changing from hammer drilling to chiselling, turn
u
the chisel to the desired position. If resistance is felt
during mode change, slightly turn the chisel to engage the
spindle lock.
Switching on and off
Select the required speed by turning the speed selector
u
dial (2).
r
s