Camera Settings; Using The Camera Setup Menu - Panasonic WV-CW974 Mode D'emploi

Camera settings

Using the Camera Setup Menu

Display the camera setup menu from the setup
menu (Advanced Menu) to configure camera
settings (page 27).
1. Display the setup menu (page 24), move the cursor to
CAMERA O, and then press the CAM (SET) button.
This will display the camera setup menu.
**CAMERA SETUP** 1/2
CAMERA ID OFF
ALC/MANUAL ALC
SHUTTER AUTO
AGC ON(MID)
SENS UP OFF
SYNC INT
WHITE BAL ATW1
DNR LOW
RESOLUTION HIGH
BW MODE
AF MODE AUTO L
**CAMERA SETUP** 2/2
×
ZOOM LIMIT 30
STABILIZER OFF
RET TOP
* The following sections numbered q to !3 explain
how to use each of the camera setup menu items.
(1) Camera ID (CAMERA ID)
See page 24 for information on the camera ID
settings method. The factory default setting is OFF.
(2) Light Control (ALC/MANUAL)
1. Move the cursor to ALC/MANUAL, and then tilt the
joystick left or right to toggle between ALC and
MANUAL.
ALC : Enables automatic lens iris adjustment in
accordance with subject brightness.
Select this ALC when using SUPER-D 3.
This is the factory default setting.
MANUAL: Adjust the lens iris with the IRIS button on
the system controller. Fixes the lens iris.
Note: The backlight
associated with this menu is described separately
and should be set up after installing the camera at
the site and observing the actual site picture.
2. If ALC is set in step 1, press the CAM (SET) button
to set SUPER-D 3.
SUPER-D 3 3 (Super Dynamic 3 3 )
When there is wide variation between the illumination of
light and dark areas of the location being monitored,
the camera adjusts the lens iris in accordance with the
bright areas. This causes loss of detail in dark areas.
Conversely, adjusting lens brightness for the dark
areas cause brighter area to become washed out.
q
w
e
r
t
y
u
i
o
!0
!1
!2
!3
compensation submenu
SUPER-D 3 digitally combines an image that is set up
for a clear view of bright areas with an image that is set
up for a clear view of dark areas, creating a final image
that preserves overall detail.
Loss of detail
in dark areas...
Notes:
• SUPER-D 3 is supported only when ALC is
selected for light control (ALC/MANUAL).
• Camera settings are limited to the following when
SUPER-D 3 is turned on.
SHUTTER : OFF, AUTO (page 29)
SENS UP : OFF, AUTO (page 29)
• If lighting conditions cause either of the following
phenomena, turn off SUPER-D 3.
(1) Screen flickering or abnormal color
(2) Digital noise in the bright areas of the screen
3. Move the cursor to SUPER-D3, and then tilt the
joystick left or right to toggle between on and off.
ON : Turns on SUPER-D 3. (Go to Step 6)
OFF : Turns off SUPER-D 3. (Go to Step 4)
This is the factory default setting.
SUPER-D3
MASK SET
LEVEL
RET TOP
4. Move the cursor to MASK SET O, and then press
the CAM (SET) button.
This will display the mask area screen, with the
cursor in the upper left cell.
5. Mask the cells in the area where background
lighting is bright. Masking an area will cause its
brightness level to be ignored.
Use the following steps to perform masking
(1) Tilt the joystick up and down, and left and right
to move the cursor to a cell you want to mask.
-28-
Wash out of
bright areas ...
Two images
digitally combined
to create a clear
final image
**ALC CONT**
BACK LIGHT COMP
OFF
•I••••• 64
- +