Safety Instructions; Initial Setup - swissflex uni 20 85RF Mode D'emploi

Health and comfort
Welcome to the world of Swissflex!
Your Swissflex uni 20_85RF/uni 22_85RF bridge
Swiss quality product. If you follow the simple opera-
ting and safety instructions, it will function to your
complete satisfaction for many years. In addition
to its many other advantages, your uni 20_85RF/uni
22_85RF bridge offers an undisturbed sleep envi-
®
ronment. All electrical connections between the
mains plug and the bed are virtually free of mains
voltage (below 0.5 watts) thanks to EcoTec.

Safety instructions

CAUTION! The uni 20_85RF/uni 22_85RF bridge
accessories must be protected from rain and other
moisture to prevent causing a fire hazard or the risk
of electric shock. In case of spillages on an accessory,
the mains cable must be disconnected from the power
outlet and checked by your Swissflex stockist.
When installing the slat base, ensure that the head,
back and foot sections are not obstructed by furniture.
Ensure that the mains supply is disconnected before
any assembly or disassembly work is carried out on
the slat base or the bed frame.
Do not connect any devices to the user socket (29)
that could endanger persons or damage objects when
the socket is turned on by remote control, in parti-
cular electrical tools such as saws, drills and similar
(risk of injury) or portable heating devices (risk of fire).
Never place the mains cable between the user socket
(29) and the bed in such a way that the cable insulati-
on could be damaged by sharp edges or twists. Never
feed the cable through the adjustment mechanism.
In the case of damage to cables to the control housing
or to the user socket (29), do not adjust the bed to
a seated position. Remove the mains plug from the
socket and inform your stockist.
Never open the user socket housing (29) to which the
cables are connected. If you interfere with any electri-
cal part of the user socket (29), the guarantee entitle-
ments will no longer apply.
Handle the uni 20_85RF/uni 22_85RF bridge
accessories with care; do not disassemble or modify
them, do not allow children to play with them and pre-
vent frail individuals from using the product without
supervision.
The product may not be used with a medical device or
be installed in a medical device.
The product may not be used in an environment in
which flammable or explosive gases or vapours (e.g.
anaesthetics) are likely to occur.
The product may not be used to raise and lower loads.
Only use spare parts that have been produced or ap-
proved by Swissflex. Only these parts guarantee ade-
quate safety.
GB
is a
®

Initial setup

Place the batteries into the radio remote control
Remove the cover from the battery compartment (19)
on the back of the radio remote control. Place 3 AAA-
batteries (20) into the compartment, paying attention
to the +/- markings. Close the compartment cover
and
®
again. The maximum range of the radio remote con-
trol is 15 metres.
Teaching-in the remote control (already taught-in in
the factory)
1. Remove the remote control's battery cover on the
back of the device.
2. Insert / check the batteries (3x AAA).
3. Activate the teach-in button (25) on the motor
(press 2x). It flashes after successful activation.
4. A small red button is located above the batteries in
the battery compartment of the device.
5. Press the button; a blue LED will start flashing.
6. Hold the button down until the blue LED is per-
manently illuminated; this means that pairing has
been completed.
Bluetooth
®
1. Download the standard „Swissflex" app from the
relevant platform for Android (Google play) or
Apple iOs (App Store).
2. Install the standard „Swissflex" app onto your
Smartphone / Tablet PC.
3. Check that the motor has a power supply and that
the Bluetooth® adapter is connected to the motor
(21).
4. The Bluetooth® connection LED flashes for about
and
®
2 min.
5. Connect your Smartphone / Tablet PC via Blu-
etooth® using the control system, also see the
Smartphone / Tablet PC instruction manual.
6. Enter the PIN (see type plate) if requested,
otherwise the Smartphone / Tablet PC connects
automatically.
7. Test the Bluetooth® connection and operation
with the Smartphone / Tablet PC.
8. The Bluetooth® connection LED turns blue as
soon as the Smartphone / Tablet PC is connected
to the control system (Bluetooth® is activated).
Operating instructions
13