Technical Specifications - Trevi TT 1070 E Mode D'emploi

Table des Matières

Les langues disponibles

ENGLISH

2. Press Album Down Or Album Up Button To Search Folder For Copying.

3. Press Rec Button, Then "One" Will Be Flashing On The Display. Press Skip Up / Skip Down Button To Select "Dir" On The Display. Press Rec

Button Again To Confirm.

4. Usb Or Sd Icon Will Be Flashing On The Display. Copying Is Performing Now.

5. When The Usb Or Sd Icon Stops Flashing, It Means That The Folder Copying Is Completed.

Iii) Copy All Track

1. Insert The Usb/Sd Storage Media, Press Cd Button To "Cd" Mode.

2. Press Rec Button, Then "One" Wll Be Flashing On The Display. Press Skip Up / Skip Down Button To Select "All" On The Display. Press Rec

Button Again To Confirm.

3. Usb Or Sd Will Be Flashing On The Display. Copying Is Performing Now.

4. When The Usb Icon Stops Flashing, It Means That All Track Copying Is Completed.

Split Track Function For Usb/Sd Recording For Turntable/Cassette/Aux In

1) Manual Split Operation Procedure: During Usb/Sd Recording, The Usb/Sd Icon Will Flash On The Display. If A New Track Is Required, Press Mode

Button On The Unit Or Remote Control, Display Will Show "Ts", Then The Unit Will Stop Recording Momentarily And Resume Again. A New File

Will Have Been Created On The Usb/Sd Device Represnting A New Track.

Auto Split Operation Procedure:

Before Usb/Sd Recording, Select Audio Source, Then Press Mode Button On The Unit Or Remote Control, Display Will Show "T-On", Which Means

The Auto Split Function Has Activated. Then Start Usb/Sd Recording, The Unit Can Automatically Detect The Silent Part Between Each Track, And

Create A New File To Move On To Start Recording The Next Track.

If Not Required: Press Mode Button On The Unit Or Remote Control Before Usb/Sd Recording, Display Will Show "T-Of", Which Means Auto Split

Has Been Deactivated.

Please Note For Auto Split: Several Seconds Of The Beginning Of The Next Track May Not Be Recorded, As The Unit May Take A Few Seconds

To Create A New File On The Usb/Sd; And It Can Additionally Be The Case That Some Music Producers Intentionally Add Silent Sections Within

One Track. As A Result, This Will Very Likely Make The Unit Consider This Silent Part The Break Between Tracks And Create A New Track On The

Recording.

Note For Auto Split: During Usb/Sd Recording From Turntable / Cassette , When The Unit Has Detected Any Particular Silent Part, The Turntable

/ Cassette Player Will Stop Momentarily. The Turntable / Cassette Player Will Resume Operation Once The Usb/Sd Device Has Begun Creating A

New File To Be Recorded.

Bluetootooth Connection

Press And Hold Function Button Till Lcd Shows "Bt", Then The Unit Is Ready For Connection With Your Bluetooh Device (Such As Mobile Phone).

Switch On The Bluetooth Function Of Your Bluetooh Device, And Select "Tt1070e" Bluetooth Equipment For Connection.

After Your Bluetooh Device Is Connected With The Unit Via Bluetooth, Start To Playback Your Device.

This Unit Has Nfc Function Which Can Allow Your Bluetooh Device (Such As Mobile Phone) Connecting With The Unit Automatically.

Switch On The Bluetooth And Nfc Function Of Your Device, Then Put It Near The

Automatically Seach And Connect With The Unit.

To Disconnect With The Unit, Put Your Device Near The "Bt/N" Logo Within 5Mm On The Front Panel Again.

Id3 Display

During Mp3 Music Playback, Press Fm St. Button On Th Remote Control, It Can Switch On Or Off Id3 Display. If Id3 Display Is On, It Can Show The

Mp3 Details (English Only) Including Tile Name, Artist Name And Album Name During Mp3 Plyback.

Earphone Jack & Line Out Socket

This System Can Be Connected With Headphone Or External Amplifier / Speaker By 3.5Mm Earphone Jack.

This System Can Be Connected With External Device (Eg. Amplifier And Speaker) By Line-Out Socket At Rear Cabinet.

Power Saving Feature:

To Save Energy, If There Is No Audio Signal From Cd / Turntable / Cassette / Usb / Sd For A Period Of Over 10 Minutes, Then The Unit Will Automatically

Switch To Standby Mode