Assembly; Troubleshooting; Motor Not Running - Xylem Goulds NPO Manuel D'utilisation

ASSE AS AS AS AS AS AS AS AS AS AS

ASSEMBLY

SE SE SEMB SE SE SE SE SE SE SE MB MB MB MB MB MB MBLY MB MB MB LY LY LY LY LY LY LY LY LY LY
If removed, replace the motor shaft deflector. Install the
motor adapter, with the drain opening DOWN, using the
four hex bolts. Torque bolts to 168 lbs. in. (19 N m).
Slide the seal housing assembly onto the motor shaft,
seating it fully and squarely against the motor adapter.
Using a quality grade O-ring lubricant, lubricate the outer
elastomer of the mechanical seal stationary seat. Fully
and squarely install the stationary seat into the seal hous-
ing. With a clean, lint free cloth, CAREFULLY wipe the
seat face clean of a lubricant or debris. DO NOT damage
the seat face.
Using a quality grade O-ring lubricant, lubricate the
inner elastomer of the mechanical seal rotary assembly.
Fully and squarely install the rotary assembly against the
stationary seat.
To install impeller, clean shaft and impeller thoroughly
with denatured alcohol and a wire brush to remove cured
Loctite from threads. Wait for parts to dry then apply
Loctite 7649 primer to threads on shaft and impeller. Al-
low 3-5 minutes for primer to dry. Apply 3 drops of Loc-
tite 243 medium strength thread-locker to shaft threads
and 2 drops on impeller threads. Tighten impeller to a
torque value of 144 lbs. in. (16 N m).
Using a quality grade O-ring lubricant, lubricate and in-
stall a new casing O-ring and internal O-ring (1SN only).
Slide the back pullout assembly into the pump casing
and secure using the eight casing cap screws. Torque the
cap screws to 70 lbs. in. (8 N m), using a cross pattern
sequence to assure the casing is pulled down evenly.
With new O-rings installed, install the casing vent and
drain plugs, tightening securely.
Assembly is complete.
TR TR TR TR TR TR TR TR TR TROU

TROUBLESHOOTING

TR OU OU OU OU OU OU OU OU OUBL OU BL BL BL BL BL BL BL BL BL BLES ES ESHO ES ES ES ES ES ES ES ES HO HO HOOT HO HO HO HO HO HO HO OTIN OT OT OT OT OT OT OT OT OT ING IN IN IN IN IN IN IN IN IN G G G G G G G G G G
FAILURE TO DISCONNECT AND
WARNING
LOCKOUT ELECTRICAL POWER
Hazardous
BEFORE ATTEMPTING ANY MAIN-
voltage
TENANCE CAN CAUSE SHOCK,
BURNS OR DEATH.
SYMPTOM

MOTOR NOT RUNNING

See Probable Causes 1 through 5
LITTLE OR NO LIQUID DELIVERED
See Probable Causes 6 through 13
EXCESSIVE POWER CONSUMPTION
See Probable Causes 3, 13, 14, 15 and 16
EXCESSIVE NOISE AND VIBRATION
See Probable Causes 3, 6, 7, 8, 10, 12, 14, 16 and 17
PROBABLE CAUSES
1. Motor thermal protector tripped
2. Open circuit breaker or blown fuse
3. Impeller binding
4. Motor improperly wired
5. Defective motor
6. Pump is not primed, air or gases in pumpage
7. Discharge, suction plugged or valve closed
8. Incorrect rotation (three phase only)
9. Low voltage or phase loss
10. Impeller worn or plugged
11. System head too high
12. NPSH too low – Excessive suction lift or losses
A
13. Incorrect impeller diameter
14. Discharge head too low – excessive flow rate
15. Fluid viscosity, specific gravity too high
16. Worn bearing
17. Pump, motor or piping loose
5