Important Safety Instructions - Cardin Elettronica SLi Série Mode D'emploi

READING THESE INSTRUCTIONS
REMARKS CAREFULLY
ALL THE PARAGRAPHS MARKED WITH THE SYMBOL
READING THESE IMPORTANT INSTRUCTIONS COULD COMPROMISE THE CORRECT WORKING ORDER OF THE SYSTEM
AND CREATE DANGER SITUATIONS FOR THE USERS OF THE SYSTEM. SAVE THESE INSTRUCTIONS FOR FUTURE USE.
THE INTEGRATED CARDIN SYSTEMS ARE DESIGNED AND BUILT ONLY
TO BE USED IN MADE TO MEASURE METALLIC STRUCTURES. CARDIN
ELETTRONICA DO NOT GUARANTEE PRODUCTS THAT HAVE BEEN
INSTALLED IN A WAY THAT DOES NOT CONFORM TO THE SUPPLIED
INDICATIONS.
CC924EFAMCB
CC24DRACOCB
It therefore follows that the structure should be constructed in such a
way as to guarantee the following characteristics:
• Suitable for housing electronic appliances;
- the upper part must be completely sealed, so as not to allow water
infiltration (IP55) (det. A);
- Air vents should be fitted in both the upper and lower parts of the columns
in order to avoid condensate build up (det. B);
• Conformity with the dimensional and structural characteristics as stipulated
by good building practice;
• The end structure should respect the parameters as laid down by the
standards and regulations in force UNI EN 12453 with regard to maintaining
safety conditions during the use of motorized gates and doors.
• These instructions are aimed at professionally qualified 'INSTALLERS OF
ELECTRICAL EQUIPMENT' and must respect the local standards and
regulations in force.
All materials used must be approved and must suit the environment in which
the installation is situated and all maintenance operations must be carried
out by professionally qualified technicians.
• This appliance must be used exclusively for the purpose for which it has been
made. 'i.e. for the automation of sliding gates' SLi724 max. weight 700
kg - SLi1024 max. weight 1000 kg - SLi24DRACO max. weight 1000 kg .
Caution! The installation of both anti-derailment buffers
is absolutely obligatory.

IMPORTANT SAFETY INSTRUCTIONS

• This appliance must never be used by people (including children) with physical,
sensory or mental disabilities or by people without specific knowledge and
experience in its operation unless they are able to benefit from the experience or
are being taught to use the appliance whilst being safeguarded by the presence of
somebody responsible for their safety.
• Before installing make sure that the guided parts are in good condition, correctly
balanced and that they open and close correctly.
• Avoid becoming trapped between the moving parts and the fixed parts during the
opening and closing movements.
• The motor's power cable must be made of polychloroprene in conformity with the
international standard 60245 IEC 57.
It is the responsibility of the installer to make sure that the following public safety
conditions are satisfied:
1) Ensure that the gate operating installation is far enough away from the main road
to eliminate possible traffic disruptions and that the size of the gate, the distance
from the road and the work cycle speed can in no way interfere, causing possible
traffic hazards.
2) The motor must be installed on the inside of the property and not on the public
side of the gate. The gates must not open onto a public area.
ATTENTION! IMPORTANT SAFETY INSTRUCTIONS
IS IMPORTANT
BEFORE PROCEEDING
C
158
FOR PERSONAL
WITH THE INSTALLATION.
IN THIS ORIGINAL INSTRUCTION MANUAL. NOT
3) The sliding gate operator is designed for use on gates through which vehicles are
passing. The gates must not be fitted with pedestrian access doors.
4) The minimum controls which may be installed are OPEN-STOP-CLOSE, these
controls must be installed at a height between 1,5 and 1,8 m and in a location not
accessible to children. Controls installed externally must be protected by a safety
device inhibiting unauthorised use.
A
5) Do not allow children to play with the operator or with the control devices.
6) At least two warning signs should be placed, where they
can be easily seen by the public, in the area of the system
of automatic operation. One inside the property and one
B
on the public side of the installation. These signs must
be indelible and not hidden by any objects (such as tree
branches, decorative fencing etc.). Make sure that the end-
user is aware that children and/or pets must not be allowed to play within the area
of a gate installation. If possible include this in the warning signs
7) Ahead of the automation a means of disconnection from the power supply must
be installed which has an opening distance on the contacts of all the poles and
ensures that the power supply is completely cut off under the conditions of a
category III overvoltage situation.
8) A correct earth connection is fundamental in order to guarantee the electrical safety
of the machine
9) If you have any questions about the safety of the gate operating system, do not
install the operator. Contact your dealer for assistance.
TECHNICAL DESCRIPTION
• The set consists of:
1 geared motor SLi724 - SLi1024 - SLi24DRACO with an incorporated encoder
without onboard electronics.
1 electronic programmer CC924FAMCB - CC24DRACOCB with NiMH batteries,
a battery charger and an integrated radio frequency module (see ZVL608).
• The geared motor is powered by 24 Vdc and is fitted with a double-reduction
kinetics system immersed in permanently fluid grease .
• The emergency manoeuvre is carried out by means of an efficient manual release
system integrated into the geared motor.
30
• The motor is connected to the electronic programmer by means of a 6-wire
fast-fitting cable.
USER INSTRUCTIONS
110 47
Attention! Only for EU customers - WEEE marking.
Q
This symbol indicates that once the products life-span has expired
it must be disposed of separately from other rubbish. The user is
therefore obliged to either take the product to a suitable differential
collection site for electronic and electrical goods or to send it
back to the manufacturer if the intention is to replace it with a
new equivalent version of the same product.
Suitable differential collection, environmental friendly treatment and disposal
contributes to avoiding negative effects on the ambient and consequently
health as well as favouring the recycling of materials. Illicitly disposing of this
product by the owner is punishable by law and will be dealt with according
to the laws and standards of the individual member nation.
During the opening/closing manoeuvre check for correct operation and activate the
emergency stop button in case of danger.
1
Warning! Entrapment danger. When using the device you are advised to wait for
the gate to completely open before crossing its threshold and to pay the maximum
attention in order to avoid becoming trapped between the hinged parts and the fixed
parts during the opening and closing movements.
During blackouts with a flat battery the gate can be released and manually manoeuvred
using the supplied release key (see manual release).
The appliance is not suitable for continuous operation and must be adjusted according
to the model (see technical data on pag. 16).
6
SAFETY. READ THE
PAY PARTICULAR ATTENTION
30
158 110 47
2
FOLLOWING
TO
AUTOMATIC OPENING
APERTURA AUTOMATICA
FERMETURE AUTOMATISÉE
AUTOMATISCHER ÖFFNUNG
Installation company: Serial number:
Product model:
Installation date:
®
Weight in kg:
riello elettronica group
ZVE: 572 - Mod: 04-09-2017