Gemini CD-150 Manuel D'instructions page 4

INTRODUCTION:
Congratulations on purchasing the Gemini CD-150 Single CD Player.
This state of the art 2U professional CD player is backed by a 1 year
warranty*. Prior to use, we suggest that you carefully read all the instruc-
tions.
FEATURES:
- Audio CD, CD-R compatible
- Anti-shock using RAM buffer memory
- Instant-start & cue with preview
- Single auto-cue/continuous play modes
- Seamless loop with reloop
- Pitch bend via jog wheel or buttons
- Three mode time selection
- Frame accurate search
- Large blue backlit LCD display
- Dual mode jog wheel for search or pitch bend
- Pitch control with range of +/- 12%
- Pitch bend buttons
- +10 track button for quick navigation
- Fully programmable with repeat function
SAFETY CERTIFICATIONS:
Laser Diode Properties
Material: Ga - Al - As
Wavelength: 755 - 815 nm (25° C)
Laser Output: Continuous Wave, max. 0.5 mW
PRECAUTIONS:
1. Do not use this CD player at temperatures below 41°F/5°C or
higher than 95°F/35°C.
2. The apparatus should not be exposed to dripping or splash-
ing, and no objects filled with liquids such as vases should be
placed on the apparatus.
3. Place the unit in a clean and dry location.
4. Do not place the unit in an unstable location.
5. When disconnecting the power cord from the AC outlet,
always grasp it by the plug. Never pull the power cord.
6. To prevent electric shock, do not remove the cover or the bot-
tom screws.
7. There are NO USER SERVICEABLE PARTS INSIDE. Please
refer to a qualified technician.
I USA ~
N THE IF YOU EXPERIENCE PROBLEMS WITH THIS UNIT CALL
S : 1 (732) 738-9003. D
ERVICE AT O NOT ATTEMPT TO RETURN THIS EQUIPMENT TO YOUR
8. Do not use chemical solvents to clean the unit.
9. Keep the laser pickup clean by keeping the tray closed.
10. Keep this manual in a safe place for future reference.
LINE VOLTAGE SELECTION:
Model CD-150 is a dual voltage unit. It will operate at 115 or
230 volts. To set the proper voltage, follow these steps:
1. Before plugging this unit into any outlet, make sure that the
VOLTAGE SELECTION SWITCH (1) is set to the proper voltage.
To change the selection, unscrew the hard plastic protective top
with a Phillips head screw driver. Then use a flat head screw
driver to move the switch to the proper selection (115V/230V).
2. Slide the switch to 115 or 230 volts.
3. Do not force or twist the switch. Excessive force may cause
damage. If the switch does not move smoothly, contact a quali-
fied technician.
G C
EMINI USTOMER
.
DEALER
CONNECTIONS:
1. Plug one end of the included RCA cable connectors into each of the
LINE OUTPUT JACKS (3) on the rear panel.
2. Plug the other end of the RCA connectors into any available line level
input jacks on your mixer. If you are connecting the CD-150 through a
receiver, you can plug the RCA connectors into the CD or AUX INPUT
JACKS on your receiver. If there are no CD or AUX INPUTS, use any
line level (not phono) inputs.
FUNCTION DESCRIPTIONS:
1. POWER: After making sure that the VOLTAGE SELECTOR SWITCH
(1), found on the rear panel of the main unit, is properly set, plug the
CD-150 POWER CORD (2) in and press the POWER (5) button. The
unit will turn ON. Pushing the POWER button (5) a second time will turn
the unit OFF.
2. DISC TRAY: The DISC TRAY (7) is where the CD is held during load-
ing, unloading and playback. Pressing the OPEN/CLOSE (6) button, will
open or close the tray. The DISC TRAY (7) holds both 12 cm and 8 cm
CDs. Please note, if the CD-150 is in play mode, the tray will not open.
NOTE: DO NOT FORCE THE DISC TRAY TO CLOSE, EXCESSIVE FORCE WILL DAMAGE
THE CD-MECHANISM, USE THE OPEN/CLOSE (6) BUTTON ONLY.
3. OPEN/CLOSE BUTTON: Press OPEN/CLOSE (6) to load or
remove a CD from the DISC TRAY.
4. DISPLAY: The DISPLAY (11) shows the track number, pitch value,
pitch bend, single, continue (for continuous play), play/pause modes,
fast forward/reverse modes, loop mode, reloop mode, PGM, repeat
modes, the playback display bar, and 3 different time displays. These
time displays are time elapsed on the track, time remaining on the disc
and time remaining on the track. Time is measured in minutes, seconds
and frames.
The PLAYBACK DISPLAY BAR, located at the top of the DISPLAY
(11), displays the elapsed and remaining time for each track at the very
top of the display. The display flashes slowly when the track has 15 sec-
onds remaining and pulses rapidly when playing time is down to 5 sec-
onds.
5. PLAY/PAUSE: Each press of the PLAY/PAUSE BUTTON (20)
causes the operation to change from PLAY to PAUSE or from PAUSE
back to PLAY. The green PLAY/PAUSE LED remains lit when in PLAY
mode, while it blinks in PAUSE mode.
6. STOP: Use the STOP (9) button to end play. This button will also
erase any CUE and LOOP settings.
7. CUE: While the unit is playing and after the cue point has been pro-
grammed, pressing CUE (21) will cause the CD player to enter the
PAUSE mode (green PLAY/PAUSE LED blinks) at the programmed cue
point (the CUE LED glows blue). Holding down the CUE (21) button
changes the function to preview and starts the CD from the programmed
CUE point. Releasing the CUE (21) button will return the CD laser to the
preset CUE (21) point.
8. TRACK SELECTION: The TRACK SELECTION (17)
buttons let you select the track to play. +10 allows you to scan through
the track selection in increments of 10. TRACK SKIP allows you to scan
through each track one at a time.
9. SEARCH JOG WHEEL: The CD-150 features an inner and outer jog
wheel that has multiple functions. Use the outer SEARCH JOG WHEEL
(8a) to select the scanning direction and speed of your CD. Slightly
angling the wheel in a clockwise direction scans forward. While a count-
er-clockwise angle scans the track in reverse. Scanning speed increas-
es as the wheel angle increases. Use the inner SEARCH DIAL WHEEL
(8) for frame accurate searching through a track in pause mode, or as a
manual pitch bend in play mode, for precise synchronization.
10. SINGLE: Pressing SINGLE (14) activates the SINGLE function. The
SINGLE function causes the unit to play one song and then stop.
Pressing the SINGLE (14) button a second time activates the CONTIN-
UOUS function causing the unit to play continuously (after the last track,
the unit will return to the first track of the disc and continue to play).
Pressing the SINGLE (14) button a third time returns to the SINGLE
function.
11. TIME: The TIME BUTTON (13) switches the time display between
the three available choices listed under the DISPLAY (11).
12. LOOP SECTION: When programming a LOOP (19) into your loop-
ing program, pressing A (green LED will light up) while the unit is play-
ing repeats the section between the entry point and the exit point where
the B (green LED will light up) button was pressed. Press B
(4)