Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
INSTALL GREASE FILTERS
Grease filters are located on the underside of microwave oven. For
installation instructions, see the User Manual packed with the microwave.
a
d
METHOD B - OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)
IMPORTANT:
•
Make sure the screws for the blower motor and blower plate are securely
tightened when they are reinstalled. This will help avoid excessive vibration.
•
Make sure the motor wiring has been properly routed and secured, and that
the wires are not pinched.
CREATE REAR WALL EXHAUST OPENING
1.
Read the instructions on the Mounting Plate/Rear Wall template.
2.
Tape the Mounting Plate/Template to the rear wall, aligning it with the holes
previously drilled for holes A and B in the mounting plate.
3.
Cut the opening, following the instructions on the Rear Wall template.
REMOVE THE BLOWER PLATE
1.
Remove and save the screw(s) fastening the blower plate to the microwave.
2.
Lift off the blower plate.
b
c
NOT E:
IT IS VER
REA D
AND FOL
Y IMPO
IN THE
RTA NT
INST ALLA
LOW THE
TO
BEF ORE
DIRE CTIO
PRO CEE
TION INST
NS
REA R
WAL L
DING
RUC TION
TEM PLA
WIT H
S
This Rear
TE.
THIS
moun ting
Wall Temp
3/8" TO EDGE
plate and
late serves
outlet.
to locate
to positio
12"
1. Use
a level
the horizo
n the bottom
accura
to check
ntal exhau
tely.
that the
st
2. Locate
and mark
templa
te is positio
right side
at least
ned
of the center
one stud
It is impor
line.
on the
left or
4"
screw mount
tant to
of the microw
ed firmly
use at
least one
ave. Mark
in a stud
wood
locatio ns
for the
two additio
to suppo
rt the weigh
3. Drill
holes in
suppli ed
nal, evenly
t
a stud,
the marke
toggle
bolts.
space d
drill a 3/16"
d locatio
Trim the
that do
not line
hole for
ns. Where
toggle
up with
wood screw
there is
bolts.
a stud,
drill 5/8"
s. For holes
DO NOT
holes for
AT THIS
INSTA
4. Remo
TIME.
LL THE
MOUN
ve the
TING PLAT
5. Revie
w the Install
templa
te from
E
install ation
ation Instru
the rear
situati on.
ction book
wall.
for your
Darle vuelta
versió n
a la hoja
en Españ
para consu
ol.
ltar la
Loca te
and mark
mou nting
hole s to
plate .
align with
IMPO RTA
hole s in
NT:
the
LOC ATE
AT LEA
THE CEN
ST ONE
TER LINE
STU D
MAR K
.
ON EITH
THE LOC
ER SIDE
SPA CED
ATIO N
OF
TOG GLE
FOR 2
ARE A.
BOL TS
ADD ITIO
IN THE
NAL , EVE
MOU NTIN
NLY
G PLA
TE
Trim the
rear wall
temp late
alon g
the dott
ed line.
Loca te
and mark
mou nting
hole s to
plate .
IMPO RTA
NT:
LOC ATE
AT LEA
THE CEN
ST ONE
TER LINE
MAR K
.
THE LOC
SPA CED
ATIO N
TOG GLE
ARE A.
BOL TS
rear wall
temp late
alon g
the dott
ed line.
align with
hole s in
the
STU D
ON EITH
ER SIDE
OF
FOR 2
ADD ITIO
IN THE
NAL , EVE
MOU NTIN
NLY
G PLA
TE
16
Surface Lights
A
Door
B
Grease Filters
C
Publicité
Chapitres
Table des Matières
