Paslode F325R Mode D'emploi page 10

PARTS LEGEND
1 511943
2 511444
3 511847
4 408302
5 513003
*
6 511413
7 513042
*
8 201756
*
9 202398
*
10 511960
* 11
539676
*
12 511876
13 511719
14 1011802
15 511799
16 511411
17 511409
*
18 502310
* 19 511970
20 511407
*
21 511447
22
* 513076
* 23 511585
24 502055
25 502050
26 404361
27 502046
28 502049
29 502061
30 502036
31 502047
32 513002
33 502058
34 502333
35 502324
*
36 502042
511713
37
502033
38
* Denotes Normal Wear Items.
** Make sure Warning Label (513092) is properly affixed.
Replace if necessary.
Label available at no charge through the Service Parts Dept.
Denotes New Change
AIR PRESSURE - PSIG
F325R ,
1 Nut, Nylon-insert 1/4"-28
1 Air Deflector
4 S.H.C.S. #10-24 x 1"
6 Flat Washer
1 Top Cap
1 Top Cap Gasket
1 Valve Spring, Main
1 O-Ring, Post
1 O-Ring, Cap
1 Poppet
1 O-Ring, Internal Poppet
1 O-Ring, External Poppet
1 Exhaust Seal
1 Flat Washer
1 S.H.C.S.1/4-28 x 1-9/16"
1 Piston "K" Seal
1 Sleeve
1 Check Valve Band
1 O-Ring, Inner Flange
1 Sleeve Flange
1 O-Ring, Outer Flange
Bumper
1
1 Driver Blade Seal
1 Compression Spring
1 Detent Body
1 Roll Pin 1/8 x 1/2"
1 Upper Work Contact Element
1 Ball Detent
1 Compression Spring
1 Thumbwheel Assembly
1 Lower Work Contact Element
1 Housing with Grip
2 Housing Label
2 Roll Pin 1/8 x 1-1/2"
1 Trigger Pin
1 O-Ring
1 Roll Pin 3/16 x 1-3/8"
1 Work Contact Element Guide
•
.090
SCF
513000
39 513066
40 502014
41 002187
42 511714
43 197913
*
44 502044
45 502059
46 196345
*
47 1015358
*
48 511446
49 502043
50 092747
*
51 502060
52 502040
53 511145
54 091866
55 502332
56 502345
57 402963
*
58 513005
59 502336
60 502019
61 502021
62 511118
63 500627
64 502020
65
403796
* 66 511196
67 513092
**
68 442681
69 502193
70 513016
71 513059
72 502017
73 404325
74 502029
75 502031
76 502038
SAFETY INSTRUCTIONS
WEAR EYE AND HEARING PROTECTION
Always wear hearing protection and eye protection
devices, including side shields when operating or
working in the vicinity of a tool.
DO NOT EXCEED MAXIMUM
RECOMMENDED AIR PRESSURE
Operate the tool using only the recommended air
operating properly and check it at least twice a day.
Never use any bottled air or gases such as oxygen
to operate the tool since they could cause the tool
to explode.
10
1 Nose Assembly with Isolators
2 Magazine Isolator
4 1/4" Lockwasher
4 S.H.C.S. 1/4-20 x 7/8"
1 O-Ring
1 Upper Trigger Valve Spool
1 Compression Spring
1 O-Ring
1 O-Ring
1 Valve Pin Assembly
1 Lower Trigger Valve Spool
1 O-Ring
1 Compression Spring
1 Trip Lever
1 Dual ModeTrigger
1 Roll Pin 1/8 x 3/4"
1 Rafter Hook
1 S.H.C.S. 5/16-18 x 5/8"
1 O-Ring
1 End Plug
2 S.H.C.S. #10-24 x 1"
1 Follower Claw
1 Lockout Bar
1 Follower Body
1 S.H.C.S. 8-32 x 1/2"
1 Compression Spring
1 Roll Pin 1/8 x 1-1/4"
1 Negator Drum/Spring Assembly
1 Warning Label
2 Lock Nut 1/4-20
1 Actuation Settings Label
2 Magazine Wear Rods
1 Magazine Assembly
2 B.H.C.S. 1/4-20 x 3/4"
2 Stop Nut 8-32
1 Magazine End Cap
1 B.H.C.S. #8-32 x 1/2"
1 B.H.C.S. #8-32 x 1"