Bestway 68086 Mode D'emploi page 3

INTRODUCTION
Proper Use
Any use other than that described or any modification of the
product is not permissible and may result in injury and/or damage
to the product. The manufacturer is not liable for damage caused by
improper use. The product is not intended for commercial use.
Description of parts and features
A
Tent Peg
1PC 8PCS
Bestway
D
Carry Bag Manual
1PC 1PC
Tent Dimensions:
Tent: 235cm x 145cm x 100cm
Pitching dimension: 245cm x 155cm
L
WARNING
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
Keep all flames and heat sources away from this tent fabric. We
recommend that you always position your tent upwind from a camp
fire. This will reduce the chances of having embers land on your
tent. In case of fire, please find the exit to escape from the fire.
Never set up the tent near the river, under the tree of other
objective hazards.
Keep exits clear.
Make sure ventilation openings are open all the time to avoid
suffocation.
SAVE THESE INSTRUCTIONS
ASSEMBLY
Setting up the tent
FIG1
1. Take the tent <A> out of the carry bag <D>, remove the strap and
release the tent <A> away from you.
WARNING: The tent <A> is under pressure and should be
handled with precaution. Release the tent <A> away from you.
303021210594_68086_14x21cm_二人快开帐篷说明书_英
Owner's Manual
Model No.#68086
COOLMOUNT 2 Tent
B
C
Guy Rope
4PCS
E
W
FIG2
2. Hammer the pegs<B> into the ground through the rings of the
tent<A> corners.(FIG1)
3. Tie one end of the guy ropes<C>onto the four corner hoops of
tent<A>.(FIG2)
4. Tie the other end onto the tent pegs<B> and fasten them by
inserting the tent pegs<B> into ground.(FIG2)
5. Note: Ensure that guy ropes<C> are about at an angle of 45°
6. Do not pull the guy ropes<C> too tight.
Repacking
A
D
A
E
C
B
E
D
B
H
NOTE: Drawing for illustration purpose only. May not reflect actual
product. Not to scale.
1. Remove the pegs <B>.
2. Gather top edge, side edge and base edge together at
center. (FIG3)
3. Left the tent up, with one hand grasp the top, side and base
edges at the cent, with the other hand push the edge with point A
downward to point B and inward to point C. (FIG4)
4. Push edges with point D and E down and inward until it forms
ring shapes on ground. (FIG5)
5. Slide rings over the top of each other and adjust rings to lie on
top of one another. (FIG6)
6. When all rings are aligned, slide strap over rings to hold them
together. (FIG7)
CLEAN AND CARE
1. Clean the tent and remove any stains with sponge and cool
water. Please use non-detergent soap for serious cleaning.
2. Never machine wash or machine dry the tent. Hand wash and air
dry.
3. Please allow all parts to dry thoroughly before you repack the
tent. This will prevent the formation from mould, bad odours and
discolouration
4. Stitch with thread to repair minor leaks, fabrics and plastic sheets
damage. Use ropes to connect broken frame parts. Use tapes to
repair the coating broken parts.
5. Silicone spray could be use onto zippers if stick
STORAGE
Store the tent in the stuff sack and place it in a cool, dry area out of
sunlight and away from heat sources and rodents.
3
D E
FIG3
A
D
E
A(C)
FIG4
B
FIG5
B
FIG7
FIG6