Oreck XL BB1000 Série Mode D'emploi page 5

Assembly
Attach Caddy and Insert Tools
fig. 1 Locate caddy clip slots at top rear corners of canister
handle. Place appliance on firm, non-slip surface or hold
in your lap. Grasp handle firmly. Place one of caddy clip
tabs inside slot on one side of handle and stretch the
other tab around handle until the opposite tab inserts in
slot.
fig. 2 Insert crevice tool, brush and fabric tool into caddy in
spaces provided.
fig. 3 Caddy will lift up 90° to allow access to the HEPA filter
cover.
Attach Shoulder Strap
fig. 4 Clamp one end of shoulder strap in front slot located at
front of handle.
fig. 5 Clamp opposite end of shoulder strap in slot at back of
handle.
fig. 6 Adjust length by pulling strap through clip.
IMPORTANT: Before using shoulder strap, pull both ends to be
sure it is secure.
Polarized Plug Notice
This product is equipped with a polarized alternating current line
plug (a plug having one blade wider than the other). This plug
will fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the outlet,
try reversing the plug. If the plug should still fail to fit, contact an
electrician to replace the obsolete outlet. Do not defeat the
purpose of the polarized plug.
To Operate
Plug cord into electrical outlet.
Power Switch
fig. 7 Push power switch to "ON" (I) position.
Hose and Tool Installation
fig. 8 The flexible hose uses a Shurlock™ locking system that
prevents hose removal unless intended. To install hose,
align "J" slot in hose coupling with tab inside the suction
port. Insert hose in port. Twist collar clockwise to lock
hose coupling in port. Twist counterclockwise and pull to
remove hose.
fig. 9 The adjustable extension wand and cleaning tools
supplied with your Oreck XL compact vacuum lock
together with friction. Twist and push to be sure they lock
tightly when installing. Twist and pull to remove.
fig.10 When installing tools directly to blower or suction port
without using hose, tool adapter tube must be used.
Adjustable Extension Wand
fig. 11 To adjust extension wand, press release button and pull
inner tube to desired length. Tube will lock when button
is released. To shorten length, press release button and
push inner tube.
E N G L I
For Easy Cord Storage
fig. 12 Wrap cord around the cord wrap and cord dump located
Blower Port
fig. 13 Remove HEPA Filter cover and filter at back of machine.
Maintenance
Changing the Filter Bag
fig. 14 Use only genuine ORECK XL filter bags. Stand unit on
fig. 15 Remove used bag and insert fresh bag. The cardboard
fig. 16 IMPORTANT: The white bag gasket glued in the housing
NOTE: The disposable inner filter bag must be replaced once a
Replacing the Micro Filter
Remove filter bag by following the Changing the Filter Bag
instructions.
fig. 17 Remove old micro filter from bottom inside unit. Replace
NOTE: A replacement filter is supplied in each package of 12
Using a HEPA-Filter and Scent Cartridge
fig. 18 Remove HEPA Filter cover at back of machine by
fig. 19 Insert Fresh Air™ Scent Cartridge on tab located in
fig. 20 Place the HEPA Filter in the filter cover.
fig. 18 Replace the HEPA Filter assembly on the canister by
NOTE: It is recommended to replace the scent cartridge when
4
S H
on bottom of the canister. To release cord, twist the cord
dump.
Firmly insert flexible hose into exhaust port.
its back. Twist knob counterclockwise to release and lift
out front plate.
rim fits smoothly into the recessed top. Align tabs on
front plate with slots in housing and replace the front
plate. Close unit by turning knob clockwise.
must be in place or unit will not operate properly.
Replace if needed.
month even if it is not full. Change it more often if it is
used in extremely dirty areas. Increase the cleaning
power of your vacuum by changing the bag often.
with new filter.
ORECK XL filter bags or you may order filters separately.
pressing down in top slot and folding back the cover. Lift
cover to remove.
center of the filter cover.
placing the bottom lip of the cover in the inside slot of
the canister and closing the cover until the top latch is
locked.
the inner filter bag is replaced.
Replace the HEPA filter every 6 months. Replace more
often if vacuum is used to pick up fine particles or in
extremely dirty areas.