Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
3. Take the top tether and pass it over the seat.
4. Place the child safety seat in the back seat of the vehicle facing in the
direction of travel.
5. Hold the safety seat with both hands and insert the two locking arms
(M)
into the verhicle´s Isofix connectors until they fasten with a click on
both sides. The red button will change to green on both sides (fig. 6.3).
6. Shake the seat to check that it is correctly anchored to the vehicle's
ISoFIX points.
IMPORTANT! The locking arms are only correctly fixed if both safety
buttons are green.
7. Push the safety seat towards the back using a firm, constant pressure
on both sides until it rests firmly against the vehicle seat (fig. 6.4). If
necessary, adjust the reclining of the vehicle´s seat backrest to ensure
that the child seat rests correctly.
8. Take the Top Tether and press the Top Tether adjuster to stretch the strap.
9. Hook the safety clasp to the Top Tether anchor point recommended in
your vehicle instruction manual (fig. 6.5).
IMPORTANT! Make sure not to use the luggage clip instead of
the Top Tether anchor clip. Look for this symbol in your vehicle:
10. To tighten the Top Tether, take up any slack by pulling the free end of the belt
through the Top Tether adjuster (fig. 6.5). The Top Tether will be correctly
tightened when the green tension indicator extends 1 mm (fig. 6.7).
Uninstalling the Isofix arms
1. To release the ISoFIX arms, pull the button on the anchors to unlock
them until the indicator turns from green to red color. This will
release the child seat (fig. 6.8).
7. removing the harness and saFety bUckle
7.1 removing the 5 point harness and the safety buckle
1. Loosen the harness straps by pulling them gently while pressing the
harness adjustment button
2. Loosen the harness straps from the back of the seat, freeing them
from the harness connector (n). Repeat the operation with the
shoulder straps connector
24
(J)
(fig. 7.1)
(P)
(fig. 7.2).
3. Pull the harness straps from the front to free them from the seat back. (fig. 7.3).
4. Take off the safety buckle, passing the retention plate through the
seat base slots (fig. 7.4). Take off the buckle (fig. 7.5).
7.2 removing the fabric cover
1. Put the headrest in the higher position (fig. 7.6).
2. Take off the headrest fabric cover (fig. 7.6).
3. Take off the fabric cover from the car seat.
8. installing the child seat. groUP 2/3
Before installing the seat for Group 2, the seat harnesses (e), harness
protectors
( d)
and buckle
(F)
must be removed. Please, for this, follow
chapter 7, section 1.
1. Ensure the seat is ready to install in forward facing group 2/3. the
indicator should be in position 2 (fig. 8.1). Pull the lever
and adjust the angle of recline to position without releasing the lever.
Release the lever when the seat is in the desired position.
2. Place the child safety seat in the back seat of the vehicle facing in the
direction of travel. Make sure it rests firmly against the vehicle seat
(fig 8.2).
9. Placing the child in the seat. groUP 2/3
1. According to the child's height the headrest can be adjusted up or down.
Place your hand on the headrest height regulator
pulling the seat down with the other hand so it does not move (8.3).
2. Place the child in the seat.
3. Pass the vehicle seat belt and buckle the vehicle seat belt until you
hear a click (fig. 8.5).
4. Make sure the abdominal belt section passes over the abdominal belt
guides
(k)
(fig. 8.4 and 8.5)
5. Pass the diagonal part of the belt through the diagonal belt guide
the headrest until it is fully extended and not twisted (fig. 8.6).
6. Take up the slack by pulling the diagonal belt section until it is as
tight-fitting as possible.
(H)
forward
(a)
and pull while
(c)
on
25
Publicité
Table des Matières
