Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
3. Place the child safety seat onto the vehicle seat, rearward facing
NoTICE! Place the EPP for headrest
4. Hold the safety seat with both hands and insert the two locking arms
into the vehicle´s Isofix connectors until they fasten with a click on both
sides. The red button will change to green on both sides (fig. 3.3).
5. Push the child safety seat against the vehicle seat until it is resting
firmly against the backrest.
6. Take the top tether strap and pressing the adjuster
strap until it is long enough to exceed the
holding the top tether brake
reach your vehicle's top tether anchor point.
7. Feed the strap through the guide situated on the back part of the
backrest
(Q)
and pass it around the side of the child safety seat,
extending it until the safety clasp is securely hooked into the top
tether anchor point recommended in your vehicle manual (fig. 3.5).
IMPORTANT! Make sure not to use the luggage clip instead of
the Top Tether anchor clip. Look for this symbol in your vehicle:
8. To tighten the Top Tether, take up any slack by pulling the free end of
the belt through the Top Tether adjuster (fig. 3.6). The Top Tether will be
correctly tightened when the red tension indicator shows in green.
9. Check the seat is correctly locked and ready to install the child (fig. 3.7).
4. Placing the child in the seat. groUP 0+/1
Proper adjustment of the height of the harness ensures the child will
be seated correctly. The harness should be adjusted to the height of
the child's shoulder or slightly above; never behind the child's back or
level with the ears (fig. 4.1).
1. Loosen the harness straps
the harness adjustment button
2. Release the buckle
(f)
to make it easier to seat the child (fig. 4.3).
3. Place the child in the seat.
4. Secure the child in the harness by joining the two parts of the clasp
and fastening the buckle
22
(s)
as shown.
(r)
(Q)
guide (fig. 3.4). By
(o)
extend the strap long enough to
(e)
by pulling them gently while pressing
(J)
(fig. 4.2).
(f)
until you hear a click (fig. 4.4).
5. Gently pull the harness adjustment strap
tension (fig. 4.5). Remember that in order to ensure the child's
safety the harnesses should fit tightly.
(i)
5. adJUsting the headrest height
Proper adjustment of the height of the headrest ensures the child will
be seated correctly. The headrest should be adjusted to ensure that
extend the
the harness straps
shoulder or slightly above; never behind the child's back or level with
the ears (fig. 4.1).
1. Loosen the harness straps
harness adjustment button
2. Adjust the headrest according to the child´s height by pulling the
headrest height regulator
child´s shoulder or slightly above (fig. 5.2).
6. installing the car seat ForWard Facing. groUP 1
For group 1 this car seat has 2 modes of installation. Although we advise to
use the seat rearward facing to the travel direction for an up to 15 months
child at least, it is possible to install the seat forward facing for a child that
exceeds 9 kg of weight, if:
• The size of the vehicle does not allow safe installation of the seat
backward facing.
• The size of the child exceeds the height percentiles and this causes the
child to be incorrectly positioned in the seat.
6.1 forward facing installation
1. Ensure the seat is not in a reclined position (the indicator should be
in position 1, 2 or 3) and is ready to install in forward position (Group
1) as shown fig. 6.1. Pull the lever
recline to the desired position (fig. 6.1)
2. Push the unlock buttons
facing installation. Move the locking arms from side to side until you
hear the click indicating that they are fully locked (fig. 6.2).
(e)
should be adjusted to the height of the child's
(e)
by pulling them gently while pressing the
(J)
(fig. 5.1).
(a)
adjusting the harness to the height of the
GROUP 1 only. From 9 months to 4 years
notice
approx. (9-18 kg)
(H)
forward and adjust the angle of
(i)
to extract both Isofix arms
(G)
to achieve the correct
(M)
for a forward
23
Publicité
Table des Matières
