Publicité
Les langues disponibles
Les langues disponibles
26
28
•
Drain condensate from pressure
vessel (29).
A
Caution!
The condensate contains oil
and must be disposed at a proper col-
lecting point.
•
Check V-belt:
− Remove belt guard (30).
− Retension V-belt or replace, if
necessary.
− To adjust the V-belt tension,
loosen the four screws at the
motor base and shift the motor.
− Tighten the screws at the motor
base again.
− Replace the belt guard.
30
Every 250 operating hours
•
Replace air intake filter element of
compressor pump.
•
Replace air filter element of filter/
regulator unit.
Every 500 operating hours
•
Drain oil from compressor pump
through the drain plug (28) and fill
with fresh oil.
A
Dispose of the waste oil envi-
ronmentally safe by taking it to a
proper collecting point!
Every 1000 operating hours
•
Have unit serviced by an authorized
service station. This will extent the
compressor's service life considera-
bly.
27
5.2
Device storage
1.
Switch unit OFF and unplug.
2.
Release pressure from tank and all
connected air tools.
3.
Store device in such way that it can-
not be started by unauthorized per-
sons.
A
Caution!
Do not store device unpro-
tected outdoors or in damp environ-
ment.
29
Do not lay device on its side for trans-
portation or storing.
6. Available Accessories
For special applications the following
accessories are available at your spe-
cialist dealer – see back cover for illus-
trations:
Sealing
A
Air Caulking Gun KP 910
for commercially available car-
tridges.
Stock-no. 090 101 0030
Sheet metal cutting
B
Air Nibbler BN 540
extra small cutting radius; cuts steel
sheet up to 1.0 mm thickness.
Stock-no. 090 100 6784
Drilling
C
Air Drill BM 310
especially handy tool for low-fatigue
working; right-hand rotation only.
Stock-no. 090 100 6725
•
Air Drill BM 500
(not illustrated) with 3/8" keyless
chuck, fully reversible with quick
reverse feature.
Stock-no. 090 105 4533
Stapling / nailing
D
Combination
Kombi 40/50
for staples (type 90) from 20 mm to
40 mm and finishing nails (type
SKN) from 20 mm to 50.
Stock-no. 090 105 4720mm.
•
Combination
Kombi 40/50
•
•
•
•
Spray painting
E
•
•
•
•
Chiselling
F
•
Tyre inflating / checking
Air
Stapler/Nailer
G
•
Air
Stapler/Nailer
ENGLISH
for staples (type 90) from 15 mm to
32 mm and finishing nails (type
SKN) from 16 mm to 32.
Stock-no. 090 105 4711mm.
Air Stapler KG 80/16
(not illustrated) for staples (type 80)
from 6 mm to 16 mm.
Stock-no. 090 105 4681
Air Stapler KG 90/25
(not illustrated) for staples (type 90)
from 15 mm to 25 mm.
Stock-no. 090 105 4690
Air Stapler KG 90/40
(not illustrated) for staples (type 90)
from 20 mm to 40 mm.
Stock-no. 090 105 4703
Air Finish Nailer SKN 50
(not illustrated) for finishing nails
(type SKN) from 20 mm to 50 mm.
Stock-no. 090 105 4738
Spray Gun FB 2200 HVLP
high-volume low-pressure feature
reduces paint mist bounce-back
and provides thicker coating at less
paint consumption.
Stock-no. 090 105 4460
Paint Spray Gun FB 2200
(not illustrated) with 0.5 l flow cup;
professional spray gun; steplessly
adjustable round, horizontal and
vertical spray pattern.
Stock-no. 090 105 4452
Paint Spray Gun SB 200
(not illustrated) with 1.0 l siphon cup.
Stock-no. 090 100 3882
Paint Spray Gun FB 150
(not illustrated) with 0.5 l flow cup;
for spraying primers and paints of
varying viskosity.
Stock-no. 090 100 3874
Paint Spray Gun FB 90
(not illustrated) with 0.75 l flow cup;
for spraying primers and paints of
varying viskosity.
Stock-no. 090 105 6064
Air Hammer Set MHS 450
for construction and auto body work
Stock-no. 090 100 9210
Air Hammer Set MHS 315
(not illustrated) to take off plaster
and tiles and for light chiselling
work.
Stock-no. 090 100 6911
Tyre Inflator Gauge RF 480
professional version (calibrated).
Stock-no. 090 105 4630
Tyre Inflator Gauge RF 363
(not illustrated) same as RF 480, but
not calibrated.
Stock-no. 090 105 4622
13
Publicité
Chapitres
