For Your Safety; Intended Use - Flex PE 14-3 125 Notice D'instruction D'origine

Polisher PE 14-3 125

For your safety

t^okfkd>
_ÉÑçêÉ=ìëáåÖ=íÜÉ=éçïÉê=íççäI=éäÉ~ëÉ=êÉ~Ç=~åÇ=
ÑçääçïW
Ó íÜÉëÉ=çéÉê~íáåÖ=áåëíêìÅíáçåëI
Ó íÜÉ="dÉåÉê~ä=mçïÉê=qççä=p~ÑÉíó=t~êåáåÖëÒ=
çå=íÜÉ=Ü~åÇäáåÖ=çÑ=éçïÉê=íççäë=áå=íÜÉ=
ÉåÅäçëÉÇ=ÄççâäÉí=EäÉ~ÑäÉíJåçKW=PNRKVNRFI
Ó íÜÉ=ÅìêêÉåíäó=î~äáÇ=ëáíÉ=êìäÉë=~åÇ=íÜÉ=
êÉÖìä~íáçåë=Ñçê=íÜÉ=éêÉîÉåíáçå=çÑ=~ÅÅáÇÉåíëK
qÜáë=éçïÉê=íççä=áë=ëí~íÉ=çÑ=íÜÉ=~êí=~åÇ=Ü~ë=ÄÉÉå=
ÅçåëíêìÅíÉÇ=áå=~ÅÅçêÇ~åÅÉ=ïáíÜ=íÜÉ=~ÅâåçïJ
äÉÇÖÉÇ=ë~ÑÉíó=êÉÖìä~íáçåëK=
kÉîÉêíÜÉäÉëëI=ïÜÉå=áå=ìëÉI=íÜÉ=éçïÉê=íççä=
ã~ó ÄÉ=~=Ç~åÖÉê=íç=äáÑÉ=~åÇ=äáãÄ=çÑ=íÜÉ=ìëÉê=
çê ~ íÜáêÇ=é~êíóI=çê=íÜÉ=éçïÉê=íççä=çê=çíÜÉê=
éêçéÉêíó=ã~ó=ÄÉ=Ç~ã~ÖÉÇK=
qÜÉ=éçäáëÜÉê=ã~ó=ÄÉ=ìëÉÇ=çåäó
Ó ~ë=áåíÉåÇÉÇI
Ó áå=éÉêÑÉÅí=ïçêâáåÖ=çêÇÉêK
c~ìäíë=ïÜáÅÜ=áãé~áê=ë~ÑÉíó=ãìëí=ÄÉ=êÉé~áêÉÇ=
áããÉÇá~íÉäóK

Intended use

The polisher is designed
– for commercial use in industry and trade,
– for all types of polishing work with
polishing sponges, lambskins and
woolskins, felt plate, buffing disc,
– for use with polishing tools which are
permitted to run at a speed of at least
3700 r.p.m.
Safety Warnings Common for
Polishing Operations
t^okfkd>
oÉ~Ç=~ää=ë~ÑÉíó=ï~êåáåÖë=~åÇ=~ää=
áåëíêìÅíáçåëK=c~áäìêÉ=íç=Ñçääçï=íÜÉ=ï~êåáåÖë=
~åÇ=áåëíêìÅíáçåë=ã~ó=êÉëìäí=áå=ÉäÉÅíêáÅ=ëÜçÅâI=
ÑáêÉ=~åÇLçê=ëÉêáçìë=áåàìêáÉëK=p~îÉ=~ää=ï~êåáåÖë=
~åÇ=áåëíêìÅíáçåë=Ñçê=ÑìíìêÉ=êÉÑÉêÉåÅÉK
 This power tool is intended to function
as a polisher. Read all safety warnings,
instructions, illustrations and speci-
fications provided with this power tool.
Failure to follow all instructions listed below
may result in electric shock, fire and/or
serious injury.
 Operations such as grinding, sanding,
wire brushing, or cutting-off are not
recommended to be performed with this
power tool.
Operations for which the power tool
was not designed may create a hazard and
cause personal injury.
 Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer.
Just because the accessory can
be attached to your power tool,
it does not assure safe operation.
 The rated speed of the accessory must be
at least equal to the maximum speed
marked on the power tool.
Accessories running faster than their rated
speed can break and fly apart.
 The outside diameter and the thickness of
your accessory must be within the
capacity rating of your power tool.
Incorrectly sized accessories cannot be
adequately guarded or controlled.
 Threaded mounting of accessories must
match the grinder spindle thread. For
accessories mounted by flanges, the
arbour hole of the accessory must fit the
locating diameter of the flange.
Accessories that do not match the
mounting hardware of the power tool will
run out of balance, vibrate excessively and
may cause loss of control.
13